User manual ROCKTRON MULTIPLEX

[. . . ] To insure against this possibility, always use good shielded cables for all audio input and output connections. Also, bundle audio cables separately from the AC power cables. These steps will help insure compliance with the Directive(s). For more information about other Rocktron products, please see your local dealer or one of our importers closest to you (listed on the enclosed warranty sheet). Copyright ©1997 Rocktron Corporation. [. . . ] Also, recalling the same preset twice via MIDI will cancel the Spillover effect and reset the new preset to its stored parameter values (only when the SPILLOVER parameter in the recalled parameter is set "OFF"). DELAY OUT 1 DLY PAN1 DLY TIME1 FINE 1 DLY RGN 1 DELAY OUT 2 DLY PAN2 DLY TIME2 FINE 2 DLY RGN 2 D>SPILLOVER 22 Functions and Parameter Descriptions REVERB Function Reverb is a multitude of echos spaced so close together that, to the human ear, seem as a single continuous sound. These echos gradually decrease in intensity until they are ultimately absorbed by the boundaries and obstacles within a room. As the sound waves from the sound source strike the boundaries of a room, a portion of the energy is reflected away from the obstacle while another portion is absorbed into it thereby causing both the continuance of sound as well as the decaying or "dying out" of the sound. ! Note!When reverb from the current preset is spilled over into the next preset recalled (SPILLOVER "ON"), the reverb parameters for the new preset will be changed to match those of the previous preset (except for the REV INPUT and SPILLOVER parameters) - even if the Reverb effect itself is switched "OUT" in the previous preset. The EFFECT LEVEL parameter in the next preset recalled does not change, therefore reverb spilled into it may be of higher or lower volume depending on the EFFECT LEVEL setting in each preset. Also, recalling the same preset twice via MIDI will cancel the Spillover effect and reset the new preset to its stored parameter values (only when the SPILLOVER parameter in the recalled parameter is set "OFF"). The PARAMETER SELECT control will allow you to access each of the following Reverb parameters: REV INPUT The REV INPUT parameter determines whether the reverb circuit is active or bypassed for the current preset. The R-MIX EFFECT/DELAY parameter is used to define the ratio of direct signal to delayed signal to be input to the reverb section. The REVERB LEVEL parameter allows you to control the level of the reverb signal at the output of the MultiValve relative to the direct signal and other effect signals. The REVERB DECAY parameter determines the length of time that the reverb signal will sound before it has completely died out. The REVERB HIGH FREQUENCY DAMPING parameter is used to control the decay rate of high frequency information in the reverb signal. The FLANGER PAN 1 parameter allows you to pan Voice 1 to the left or right channel. The FLANGER DEPTH 1 parameter adjusts the amount of modulation of Voice 1. Lower DEPTH settings produce more subtle effects, while higher settings will result in a more drastic effect. The FLANGER RATE 1 parameter determines the speed at which Voice 1 is modulated. The TIME1 parameter determines the multiplier by which a new modulation rate will be selected for the RATE 1 parameter when the Tap Delay feature of the MultiValve is used. (See Section 7: "Tap Delay" for more information on the Tap Delay feature. ) The FLANGER OUTPUT 2 parameter determines the overall volume of Voice 2. The FLANGER PAN 2 parameter allows you to pan Voice 2 to the left or right channel. The FLANGER DEPTH 2 parameter adjusts the amount of modulation of Voice 2. Lower DEPTH settings produce more subtle effects, while higher settings will result in a more drastic effect. The FLANGER RATE 2 parameter determines the speed at which Voice 2 is modulated. The TIME2 parameter determines the multiplier by which a new modulation rate will be selected for the RATE 2 parameter when the Tap Delay feature of the MultiValve is used. [. . . ] If you have altered and stored presets which you do not want to erase, do not perform the following procedure. 3 4 2 1 Step 1 Turn the FUNCTION SELECT control clockwise to "FACTORY RESTORE". FACTORY RESTORE Step 2 Turn the PARAMETER SELECT control two steps clockwise to "ALL RESTORE 0". ALL RESTORE 0 Step 3 A specific code number must be entered to restore the MultiValve memory. Use the PARAMETER ADJUST control to enter the number "243". ALL RESTORE 243 !!WARNING !! Pressing the STORE button at this time will permanently erase all user presets and replace them with the original factory presets. If you have altered and stored presets which you do not want to erase, turn the FUNCTION SELECT control to exit this function. 62 Operating the MultiValve Step 4 Press the STORE button at this time to initiate the All Restore procedure and erase all current MultiValve presets, replacing them with the original factory presets. [. . . ]