User manual ROCKTRON PROGAPULTRA

[. . . ] These steps will help insure compliance with the Directive(s). For more information about other Rocktron products see the last section in this manual, or see your local dealer or one of our importers closest to you (listed on the Rocktron website www. rocktron. com). Copyright ©2003 GHS Corporation. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This parameter is also controlled by the knob labelled BASS when not in the EDIT MODE The BASS FREQUENCY parameter allows you to select a center frequency between 63Hz and 500Hz to be cut or boosted by the BASS LEVEL parameter. The BASS BANDWIDTH parameter determines (in octaves) the width of the selected bass band. The MID LEVEL parameter allows you to cut or boost the mid band frequencies by up to 15dB. This parameter is also controlled by the knob labelled MIDDLE when not in the EDIT MODE. The MID FREQUENCY parameter determines a mid band center frequency between 250Hz and 2KHz to be cut or boosted via the MID LEVEL parameter. The MID BANDWIDTH parameter determines (in octaves) the width of the selected mid band. The TREBLE LEVEL parameter allows you to cut or boost the high band frequencies by up to 15dB. This parameter is also controlled by the knob labelled TREBLE when not in the EDIT MODE. The TREBLE FREQUENCY parameter determines a high band center frequency between 1KHz and 8KHz to be cut or boosted via the TREBLE LEVEL parameter. The TREBLE BANDWIDTH parameter determines (in octaves) the width of the selected high band. The PRESENCE LEVEL parameter allows you to cut or boost an additional high band frequency by up to 15dB. Source 1 is the Voice 1 output from the previous effect in the signal chain (chorus, flanger, pitch shifter, etc. ), while Source 2 may be the Voice 2 output from the previous effect in the signal chain or the direct signal (selectable via the SOURCE 2 parameter). (Refer to the block diagram shown on page 13 for a visual representation of the input to the Delay section. ) TIME2 DELAY LVL D-MIX S1/S2 20 Functions and Parameter Descriptions SOURCE 2 This parameter is used to select whether the Source 2 input will be the VOICE 2 output from the previous effect in the signal chain or the DIRECT signal. In configurations where there is no effect immediately preceding the delay, both Source 1 and Source 2 will be the direct signal. The DELAY HIGH FREQUENCY DAMPING parameter controls the amount of high frequency content in the delayed and regenerated signals. Higher amounts of damping will result in less high frequency information in the delayed signal. The DELAY OUT 1 parameter determines the volume of Delay 1. The DLY PAN1 parameter allows you to pan the Delay 1 signal to the left or right channel. The DELAY TIME1 parameter determines the length of time (in 10 milliseconds increments) after the input signal that the Delay 1 signal will begin. The DELAY TIME can be adjusted via the PARAMETER ADJUST control, MIDI controller changes or via the Tap Delay feature. The FINE 1 parameter allows for adjustment of Delay 1 in 1 millisecond increments. The DLY RGN 1 parameter determines how many times the Delay 1 signal is fed back into the input and repeated. [. . . ] Sequence mode will dump the information back to the Blue Thunder at the same rate as it was received from the Blue Thunder. The Blue Thunder can receive a data dump at about 65Hz (or about 1 byte every 15 milliseconds). 51 Operating the Blue Thunder Factory Restore The Factory Restore function allows you to restore altered Blue Thunder presets to their original condition as shipped from the factory. Either the entire Blue Thunder memory can be restored, a single preset can be restored to any preset location, or the controller information alone can be restored. Restoring a single factory preset: Step 1 Press the EDIT button to enter the "EDIT MODE" EDIT MODE Step 2 Turn the FUNCTION SELECT control clockwise to "FACTORY RESTORE". FACTORY RESTORE Step 3 Turn the PARAMETER SELECT control one step clockwise to "RESTR 1 TO 1". The number on the left is the original factory preset number to be restored. [. . . ]