User manual ROLAND ADA-8024

[. . . ] Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's Manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. fig. 0(frontpanel) All product names mentioned in this document are trademarks or registered trademarks of their respective owners. Copyright © 1999 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. [. . . ] At present (December 1999), no devices with a 96 kHz compatible R-BUS connector are available. For details, please contact your nearest Roland Service Center, authorized Roland distributor, or your dealer. 8 POWER Switch This turns the power of the ADA-8024 on/off. 8 Front and Rear Panels Rear Panel fig. 2 3 5 1 1 AC IN 2 4 6 Connect the included power cable here. To avoid malfunction, connect only the power supply cord that was supplied with the unit. 2 WORD CLOCK IN/OUT Connectors IN: When supplying a sampling clock from an external device to the ADA-8024, input the WORDCLOCK signal here. Use this when you want the reference clock to be another device that outputs a high-precision sampling clock, or when synchronizing to a device that has only a WORDCLOCK OUT. fig. 3. e Sampling Clock Master Digtal Tape Recorder WORD CLOCK OUT TERMINATOR SWITCH: ON WORD CLOCK IN ADA-8024 CLOCK SOURCE: WORD CLOCK · If you have selected "WORD CLOCK" as the sampling clock of the ADA-8024, you must set the master clock of the connected device to the R-BUS to which that ADA-8024 is connected. · If the master clock of the device connected to the R-BUS connector is the word clock signal, you must select "R-BUS" as the sampling clock of the ADA-8024. 9 Front and Rear Panels TERMINATOR Switch: Turn this on if the ADA-8024 is the last device in the word clock signal chain. Turn this off only if you are using a relay connector to distribute the word signal to other devices. fig. 3a. e Sampling Clock Master Digtal Tape Recorder Connector TERMINATOR SWITCH: OFF WORD CLOCK IN WORD CLOCK IN ADA-8024 CLOCK SOURCE: WORD CLOCK WORD CLOCK SLAVE OUT: This outputs the sampling clock on which the ADA-8024 is operating. Use this when you want another device to synchronize to the sampling clock on which the ADA-8024 is operating. 3 R-BUS (RMDB2) Connector This is an 8-in/8-out 24 bit digital audio connector. Connect it to another device that has an R-BUS connector (e. g. , Roland digital mixer or Roland digital recorder). Connect the R-BUS (RMDB2) connector only to an R-BUS equipped device. To avoid malfunctions, never connect it to a SCSI connector, an RS-232C connector, or a parallel connector, even if the connector has the same shape. Use a special R-BUS (RMDB2) cable to make connections. of a work (CD recording, video recording, broadcast, etc. ) whose copyright is owned by a third party. Roland will take no responsibility for any infringement of copyright that you may commit in using the ADA-8024. Disclaimer of liability Roland will take no responsibility for any "direct damages, " "consequential damages, " or "any other damages" which may result from your use of the ADA-8024. These damages may include but are not limited to the following events which can occur when using the ADA-8024. · Any loss of profit that may occur to you · Permanent loss of your music or data · Inability to continue using the ADA-8024 itself or a connected device About the License Agreement The ADA-8024 and its CD-R capability are designed to allow you to reproduce material to which you have copyright, or material which the copyright owner has granted you permission to copy. Accordingly, reproduction of music CDs or other copyrighted material without the permission of the copyright owner, other than for your own personal use and enjoyment (private use) constitutes copyright infringement, which may incur penalties. Consult a copyright specialist or special publications for more detailed information on obtaining such permission from copyright holders. 14 Troubleshooting If the ADA-8024 does not function correctly, please check the following points before you suspect a malfunction. If checking these points does not resolve the problem, please contact Roland, a nearby Roland service center, or your dealer. The CLOCK SOUCE R-BUS (RMDB2) indicator is blinking. No sampling clock is being input to the R-BUS connector of the ADA-8024. Make the correct master clock settings on the device connected to the R-BUS connector (p. Alternatively, select a different sampling clock. The CLOCK SOURCE WORD CLOCK indicator is blinking. A word clock signal is not being input correctly. Make the correct connections on the device that is supplying the word clock (p. Alternatively, select another sampling clock. The sound that is input to the ADA-8024 is not output from the device (digital mixer, digital recorder) that is connected to the R-BUS connector of the ADA-8024. · Has the correct sampling clock (master clock) been selected on the ADA-8024 and on the device connected to the ADA-8024's R-BUS connector? [. . . ] Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 498 3079 BRAZIL Roland Brasil Ltda Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666 FINLAND Roland Scandinavia As, Filial Finland Lauttasaarentie 54 B Fin-00201 Helsinki, FINLAND TEL: (9) 682 4020 UNITED KINGDOM Roland (U. K. ) Ltd. Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 700139 NORTH AMERICA CANADA Roland Canada Music Ltd. (Head Office) 5480 Parkwood Way Richmond B. C. , V6V 2M4 CANADA TEL: (0604) 270 6626 INDONESIA PT Citra IntiRama J1. [. . . ]