User manual ROLAND C-380

[. . . ] IMPORTANT SAFETY INSTRUCTIONS WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING - When using electric products, basic precautions should always be followed, including the following: 1. Do not block any of the ventilation openings. [. . . ] · If you press a MAN II division memory [1]­[5] piston, the current settings of the MAN II division memory [1]­[5] pistons will be stored in the bank. Please be aware that the information that was previously stored in the memory bank will be overwritten and lost. 48 Storing a Combination of Stops Recalling a Registration from a Different Memory Bank 1. From the main screen, use the memory bank select [M­]/[M+] pistons to select the number of the memory bank that you want to recall. If you hold down the memory bank select [M­]/[M+] piston, the memory bank number will continue changing consecutively. Simply pressing a memory bank select [M­]/[M+] piston will not recall a registration. 2. Press one of the general memory pistons or division memory pistons (C-380 only). · If you press a general memory [1]­[5] piston, the corresponding registration will be recalled from the general memory bank you selected in step 1. · If you press a MAN I division memory [1]­[5] piston, the corresponding registration will be recalled from the MAN I division memory bank. · If you press a MAN II division memory [1]­[5] piston, the corresponding registration will be recalled from the MAN II division memory bank. Recalling Registrations Successively Simply by pressing the [NEXT] piston, or the [PREV] piston (C-380 only), you can successively recall the registrations that are stored at the general pistons. For example, if you will be performing a recital, you can use the memories to store your registrations in the order in which you will be using them, and then smoothly switch to the next registration while you perform. fig. piston-2. eps M01 Each press recalls the next registration M02 M20 1 2 3 4 5 6 7 8 9 10 99 100 Each press recalls the previous registration Even if you press the [NEXT] piston after arriving at number 5 of memory bank M20, you will stay at memory bank M20 number 5. You can also assign the function of the [NEXT] piston, or the [PREV] piston (C-380 only) to a kick switch so that you can use your foot to switch between registrations (p. After using [M­] [M+] pistons to change the memory bank, pressing the [NEXT] piston will select the next piston of the newly selected memory bank. 49 Practicing Along with a Preset Song or Performance Data You can practice by playing along with preset songs (demo songs) that are built into the organ, or with performance data that you've recorded from your own playing (p. 56). · · · · You can mute (silence) the performance of a specific division (p. You can listen to the performance of a specific division as a guide tone (p. When a song is played back, the registrations that were used at the time it was recorded will automatically be called up. If you wish to preserve the current overall status of the organ, make sure to save your settings to a memory piston beforehand (p. · Playback will use the currently specified reverb (p. · Songs can also be played back in succession. Start from the state where playback is stopped. Then, using the [Select/Menu] knob, select "Play Mode. " Next, turn the [Value/Exit Menu] knob to change the setting to "CHAIN. " Setting OFF CHAIN Explanation Play back only the selected song Consecutively play back all the songs on the selected media Selecting and Playing Back a Song fig. rec-play-2. eps 1. If you want to play back a song from USB memory, connect your USB memory to the external memory connector (p. From the main screen, press the [STOP] piston to access the "Song Recorder" screen. fig. LCD034. eps 3. Turn the [Select/Menu] knob to select the media type field in the upper right. fig. LCD033. eps 50 Practicing Along with a Preset Song or Performance Data 4. Turn the [Value/Exit Menu] knob to select the media on which the song is stored. Setting USB INT PRE Explanation Play back song data from USB memory Play back song data from internal memory Play back built-in preset song (demo song) * For more information about the built-in preset songs, refer to "List of Preset Song/Demo Song" (p. [. . . ] 73 Volume Expression Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 External Audio Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 External MIDI Sound Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Guide Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]