User manual ROLAND CY-12C

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the Roland CY-12R/C V-Cymbal. Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" (p. 3­4) and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. [. . . ] Contact between the cable and the cymbal or stand can result in problems, 5 Next such as double sounding. 3. Make the trigger settings for the percussion sound module. 2. The TDW-1 with V-Cymbal Control Owner's Manual contains an explanation of how the CY-15R is used with Three Way Triggering. Substitute "CY-12R/C" for "CY-15R" as you read through the text. Should you neglect to make the appropriate settings for the percussion sound module. · Sometimes it does not sound (uneven volume) · The volume is too low (reduced sensitivity) · Double sounding may occur For information on how to change the parameters for a percussion sound module, refer to its owner's manual. Playing Methods Bow Shot This is the most common playing method, playing the pad face of the cymbal. It corresponds to the sound of the "head-side" of the connected trigger input. If Using TD-10 + TDW-1 with V-Cymbal Control When you use the TD-10 + TDW-1 V-Cymbal Control, three way triggering is possible. * Three Way Triggering is not available with the TD-8. Bow Edge Shot This playing method involves striking the edge with the shoulder of the stick. It corresponds to the sound of the "rimside" of the connected trigger input. About Three Way Triggering By using two cables to connect the CY-12R/C and a TD-10, you can then perform using three different tones: bow, bell, and edge. TDW-1 specifications allow the Three Way Triggering function to be used with only one V-Cymbal. For example, if you use the Three Way Triggering function with one CY-15R, you would not be able to use Three Way Triggering if you added another CY-12R/C. To make use of edge shot, you'll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots. Edge sensor Connections/Examples of Settings CY-12R/C Output BOW/BELL BOW/EDGE TD-10 Trigger Input 10/RIDE 11/AUX1 TD-10 Trigger Type RdA CTR Bell Shot This playing method involves striking the bell. It corresponds to the sound of the "rim-side" of the connected trigger input. If you connect a pad or a V-Cymbal ONLY to the trigger input for which trigger type is set to the "CTR"(11/AUX 1), it will not work. Correspondences Between Playing Methods and Trigger Input Playing Methods Bow Shot Bell Shot Edge Shot TD-10 Trigger Input 10/RIDE Head 10/RIDE Rim 11/AUX 1 Rim · To make use of bell shot, you'll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots. · Use the shoulder of the stick when playing bell shots. Bell * Head-side tones for the trigger input 11/AUX 1 cannot be sounded. For more details on the settings for Three Way Triggering, refer to the TDW-1 with V-Cymbal Control Owner's Manual. 6 Next Choking Choking (pinching) the cymbal's edge with the hand immediately after hitting the cymbal makes the sound stop. Double sounding · Are any cables touching the CY-12R/C?Secure the cables in place with the cable ties so that they do not touch the units. Also, be careful to make sure that the cables are not pulled by the movement of a cymbal when struck (p. · Are the stopper, felt washer, and wing nut attached correctly?Double triggering may occur if the stopper and/or wing nut is loose. Use a tuning key (drum key) to tighten properly. * If double triggering still occurs, try adjusting trigger parameters, such as Retrigger Cancel, on the sound module you are using (TD-6, TD-8, TD-10, etc. ) To make use of choking play techniques, you'll need to connect to a trigger input jack on the percussion sound module that accommodates rim shots. fig. CY07. e Edge sensor The volume level is too low · If the cymbal is struck while power to the drum module (such as the TD-6, TD-8, or TD-10) is turned on, the response to light hits will be poor. Do not strike pads or cymbals while turning on the power. Troubleshooting Issues Affecting The Overall System Check these first · Is the trigger type set correctly?Make the trigger parameter settings for your percussion sound module (p. · Is a monaural cable being used? [. . . ] S-131 30 Nacka SWEDEN TEL: (08) 702 0020 Shanghai Xingtong Acoustics Equipment CO. , Ltd. Rm. 1108, No. 2240 Pudong South Road Shanghai, CHINA TEL: (021) 6873 4123 HONG KONG Tom Lee Music Co. , Ltd. Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911 CENTRAL/LATIN AMERICA ARGENTINA Instrumentos Musicales S. A. Florida 656 2nd Floor Office Number 206A Buenos Aires ARGENTINA, CP1005 TEL: (54-11) 4- 393-6057 DENMARK Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: (039)16 6200 TURKEY Barkat muzik aletleri ithalat ve ihracat Ltd Sti Siraselviler cad. Guney is hani 8486/6, Taksim. TURKEY TEL: (0212) 2499324 SWITZERLAND Roland (Switzerland) AG Musitronic AG Gerberstrasse 5, Postfach, CH-4410 Liestal, SWITZERLAND TEL: (061) 921 1615 FRANCE Roland France SA 4, Rue Paul Henri SPAAK, Parc de l'Esplanade, F 77 462 St. Thibault, Lagny Cedex FRANCE TEL: 01 600 73 500 U. A. E. Zak Electronics & Musical Instruments Co. [. . . ]