User manual ROLAND OP-R09HR-C

[. . . ] (Initial value is ON) For Drum Parts, not received when Rx. NOTE ON = OFF for each Instrument. n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Volume: 00H-7FH (0-127), Initial Value = 64H (100) * * Volume messages are used to adjust the volume balance of each Part. (Initial value is ON) qPolyphonic Key Pressure Status AnH 2nd bytes kkH 3rd byte vvH rPan (Controller number 10) Status BnH 2nd bytes 0AH 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) kk = note number: 00H-7FH (0-127) vv = key pressure: 00H-7FH (0-127) * * Not received when Rx. POLY PRESSURE (PAf) = OFF. (Initial value is ON) The resulting effect is determined by System Exclusive messages. With the initial settings, there will be no effect. n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = pan: 00H-40H-7FH (Left-Center-Right), Initial Value = 40H (Center) * * * For Rhythm Parts, this is a relative adjustment of each Instrument's pan setting. [. . . ] If "Data Set 1" is transmitted successively, there must be an interval of at least 40 ms between packets. Regarding the checksum please refer to section 4 (p. 13). rHold 1 (Controller number 64) Status BnH 2nd bytes 40H 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Control value: 00H-7FH (0-127) rSostenuto (Controller number 66) Status BnH 2nd bytes 42H 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON rSoft (Controller number 67) Status BnH 2nd bytes 43H 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Control value: 00H-7FH (0-127) rEffect 1 (Reverb Send Level) (Controller number 91) Status BnH 2nd bytes 5BH 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Control value: 00H-7FH (0-127) rEffect 3 (Chorus Send Level) (Controller number 93) Status BnH 2nd bytes 5DH 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Control value: 00H-7FH (0-127) 7 qProgram Change Status CnH 2nd bytes ppH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) pp = Program number: 00H-7FH (prog. 1-prog. 128) sSystem Realtime Message qRealtime Clock Status F8H qActive sensing Status FEH * This will be transmitted constantly at intervals of approximately 250 ms. sSystem exclusive messages rIdentity Reply Status F0H Byte F0H 7EH 10H 06H 02H 41H 42H 00H 00H 09H 00H 01H 00H 00H F7H Data byte 7EH, 10H, 06H, 02H, 41H, 42H, 00H, 00H, 09H, 00H, 01H, 00H, 00H Explanation Exclusive status ID number (universal non-realtime message) Device ID (use the same as the device ID of Roland) Sub ID#1 (General Information) Sub ID#2 (Identity Reply) ID number (Roland) Device family code (LSB) Device family code (MSB) Device family number code (LSB) Device family number code (MSB) Software revision level Software revision level Software revision level Software revision level EOX (End of Exclusive) Status F7H 8 3. Parameter Address Map (Model ID = 42H) This map indicates address, size, Data (range), Parameter, Description, and Default Value of parameters which can be transferred using and "Data set 1 (DT1). " All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form. sAddress Block map An outlined address map of the Exclusive Communication is as follows; Address (H) 40 00 00 40 01 3F 40 1x 00 40 2x 5A 41 m0 00 41 m8 7F 48 00 00 48 01 10 48 1D 0F 49 m0 00 49 mE 17 Block +------------------------------------------------------------------------+ | SYSTEM PARAMETERS |Individual +------------------------------------------------------------------------+ +------------------------------------------------------------------------+ | PART PARAMETERS |Individual | (x = 0-F) | +------------------------------------------------------------------------+ +------------------------------------------------------------------------+ | SRUM SETUP PARAMETERS |Individual | (m = 0-1) | +------------------------------------------------------------------------+ +------------------------------------------------------------------------+ | SYSTEM PARAMETERS |Bulk +------------------------------------------------------------------------+ | PART PARAMETERS |Bulk +------------------------------------------------------------------------+ +------------------------------------------------------------------------+ | DRUM SETUP PARAMETER |Bulk | (m = 0-1) | +------------------------------------------------------------------------+ There are two ways in which GS data is transmitted: Individual Parameter Transmission in which individual parameters are transmitted one by one, and Bulk Dump Transmission in which a large amount of data is transmitted at once. sIndividual Parameters Individual Parameter Transmission transmits data (or requests data) for one parameter as one exclusive message (one packet of "F0 . . . . . In Individual Parameter Transmission, you must use the Address and Size listed in the following "Parameter Address Map. " Addresses marked at "#" cannot be used as starting addresses. qSystem Parameters Parameters related to the system of the device are called System Parameters. Address (H) 40 00 00 40 00 01# 40 00 02# 40 00 03# * Size (H) 00 00 04 Data (H) 0018-07E8 Parameter MASTER TUNE Description -100. 0 - +100. 0 [cent] Use nibblized data. Default Value (H) 00 04 00 00 Description 0 [cent] Refer to section 4. Supplementary material, "About tuning" (p. 00 00 01 00 00 01 00 00 01 00 00 01 00-7F 28-58 01-7F 00 MASTER VOLUME MASTER KEY-SHIFT MASTER PAN MODE SET 0-127 (= F0 7F 7F 04 01 00 vv F7) -24 - +24 [semitones] -63 (LEFT) - +63 (RIGHT) 00 = GS Reset, 127 = Exit GS (Rx. only) 7F 40 40 127 0 [semitones] 0 (CENTER) 40 00 04 40 00 05 40 00 06 40 00 7F * Refer to "System exclusive messages related to mode settings" (p. 00 00 10 00-40 VOICE RESERVE Part 10 (Drum Part) Part 1 Part 2 Part 3 Part 4 Part 5 Part 6 Part 7 Part 8 Part 9 Part 11 : Part 16 02 06 02 02 02 02 02 02 02 02 00 00 2 6 2 2 2 2 2 2 2 2 0 0 40 01 10 40 01 11# 40 01 12# 40 01 13# 40 01 14# 40 01 15# 40 01 16# 40 01 17# 40 01 18# 40 01 19# 40 01 1A# 40 01 :# 40 01 1F# * The sum total of voices in the voice reserve function must be equal to or less than the number of the maximum polyphony. This parameter differs from the conventional Fine Tuning (RPN #1) parameter in that the amount of frequency alteration (in Hertz) will be identical no matter which note is played. When a multiple number of Parts, each of which has been given a different setting for PITCH OFFSET FINE, are sounded by means of an identical note number, you can obtain a Celeste effect. 10 40 1x 19 40 1x 1A 40 1x 1B 40 1x 1C 40 1x 1D 40 1x 1E 40 1x 1F 40 1x 20 40 1x 21 40 1x 22 40 1x 23 * * * 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-5F 00-5F 00-7F 00-7F 00-01 PART LEVEL 0-127 (= CC# 7) VELOCITY SENSE DEPTH 0-127 VELOCITY SENSE OFFSET 0-127 PART PANPOT -64 (RANDOM), -63 (LEFT) - +63 (RIGHT) (= CC# 10, except RANDOM) KEY RANGE LOW (C-1)-(G9) KEY RANGE HIGH (C-1)-(G9) CC1 CONTROLLER NUMBER 0-95 CC2 CONTROLLER NUMBER 0-95 CHORUS SEND LEVEL 0-127 (= CC# 93) REVERB SEND LEVEL 0-127 (= CC# 91) Rx. BANK SELECT OFF/ON 64 40 40 40 00 7F 10 11 00 28 01 (00*) 100 64 64 0 (CENTER) C-1 G9 16 17 0 40 ON (OFF*) "Rx. BANK SELECT" is set to OFF by "GM1 System On, " and Bank Select message will be ignored. "Rx. BANK SELECT" is set to ON by "GM2 System On. " "Rx. BANK SELECT" is set to ON by power-on Reset or by receiving "GS RESET. " 00 00 01 00-01 Rx. BANK SELECT LSB OFF/ON 00 OFF 40 1x 24 * OP-R09HR-C can be recognise Bank Select LSB (40H-43H) even if this message is OFF. 00 00 01 00 00 03 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-01 00-7F 0E-72 0E-72 0E-72 0E-72 0E-72 0E-72 0E-72 0E-72 TONE REMAIN Bank Select LSB Range TONE MODIFY 1 Vibrato rate (= NRPN# 8) TONE MODIFY 2 Vibrato depth (= NRPN# 9) TONE MODIFY 3 TVF cutoff frequency (= NRPN# 32) TONE MODIFY 4 TVF resonance (= NRPN# 33) TONE MODIFY 5 TVF&TVA Env. attack (= NRPN# 99) TONE MODIFY 6 TVF&TVA Env. decay (= NRPN# 100) TONE MODIFY 7 TVF&TVA Env. release (= NRPN# 102) TONE MODIFY 8 Vibrato delay (= NRPN# 10) SCALE TUNING C SCALE TUNING C# SCALE TUNING D SCALE TUNING D# SCALE TUNING E SCALE TUNING F SCALE TUNING F# SCALE TUNING G SCALE TUNING G# SCALE TUNING A SCALE TUNING A# SCALE TUNING B OFF/ON LSB (from) LSB (to) -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 -50 - +50 01 40 43 40 40 40 40 40 40 40 40 ON 40H 43H 0 0 0 0 0 0 0 0 40 1x 25 40 1x 28 40 1x 29# 40 1x 30 40 1x 31 40 1x 32 40 1x 33 40 1x 34 40 1x 35 40 1x 36 40 1x 37 40 1x 40 40 1x 41# 40 1x 42# 40 1x 43# 40 1x 44# 40 1x 45# 40 1x 46# 40 1x 47# 40 1x 48# 40 1x 49# 40 1x 4A# 40 1x 4B# * 00 00 0C 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] -64 - +63 [cent] 40 40 40 40 40 40 40 40 40 40 40 40 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] 0 [cent] SCALE TUNING is a function that allows fine adjustment to the pitch of each note in the octave. The pitch of each identically-named note in all octaves will change simultaneously. A setting of +/- 0 cent (40H) is equal temperament. Supplementary material, "The Scale Tune Feature"(p. 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 40-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 28-58 00-7F 00-7F MOD PITCH CONTROL MOD TVF CUTOFF CONTROL MOD AMPLITUDE CONTROL MOD LFO1 RATE CONTROLMOD LFO1 PITCH DEPTH MOD LFO1 TVF DEPTH0 MOD LFO1 TVA DEPTH0 MOD LFO2 RATE CONTROL MOD LFO2 PITCH DEPTH0 MOD LFO2 TVF DEPTH0 MOD LFO2 TVA DEPTH0 BEND PITCH CONTROL BEND TVF CUTOFF CONTROLBEND AMPLITUDE CONTROL BEND LFO1 RATE CONTROL BEND LFO1 PITCH DEPTH0 BEND LFO1 TVF DEPTH0 BEND LFO1 TVA DEPTH0 BEND LFO2 RATE CONTROL BEND LFO2 PITCH DEPTH0 BEND LFO2 TVF DEPTH0 BEND LFO2 TVA DEPTH0 CAf PITCH CONTROL CAf TVF CUTOFF CONTROL CAf AMPLITUDE CONTROL -24 - +24 [semitone] -9600 - +9600 [cent] -100. 0 - +100. 0 [%] 10. 0 - +10. 0 [Hz] 0-600 [cent] -2400 [cent] -100. 0 [%] -10. 0 - +10. 0 [Hz] -600 [cent] -2400 [cent] -100. 0 [%] 0-24 [semitone] 9600 - +9600 [cent] -100. 0 - +100. 0 [%] -10. 0 - +10. 0 [Hz] -600 [cent] -2400 [cent] -100. 0 [%] -10. 0 - +10. 0 [Hz] -600 [cent] -2400 [cent] -100. 0 [%] -24 - +24 [semitone] -9600 - +9600 [cent] -100. 0 - +100. 0 [%] 40 40 40 40 0A 00 00 40 00 00 00 42 40 40 40 00 00 00 40 00 00 00 40 40 40 0 [semitones] 0 [cent] 0 [%] 0 [Hz] 47 [cent] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 2 [semitones] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [semitones] 0 [cent] 0 [%] 40 2x 00 40 2x 01 40 2x 02 40 2x 03 40 2x 04 40 2x 05 40 2x 06 40 2x 07 40 2x 08 40 2x 09 40 2x 0A 40 2x 10 40 2x 11 40 2x 12 40 2x 13 40 2x 14 40 2x 15 40 2x 16 40 2x 17 40 2x 18 40 2x 19 40 2x 1A 40 2x 20 40 2x 21 40 2x 22 11 40 2x 23 40 2x 24 40 2x 25 40 2x 26 40 2x 27 40 2x 28 40 2x 29 40 2x 2A 40 2x 30 40 2x 31 40 2x 32 40 2x 33 40 2x 34 40 2x 35 40 2x 36 40 2x 37 40 2x 38 40 2x 39 40 2x 3A 40 2x 40 40 2x 41 40 2x 42 40 2x 43 40 2x 44 40 2x 45 40 2x 46 40 2x 47 40 2x 48 40 2x 49 40 2x 4A 40 2x 50 40 2x 51 40 2x 52 40 2x 53 40 2x 54 40 2x 55 40 2x 56 40 2x 57 40 2x 58 40 2x 59 40 2x 5A 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 28-58 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F CAf LFO1 RATE CONTROL CAf LFO1 PITCH DEPTH CAf LFO1 TVF DEPTH CAf LFO1 TVA DEPTH CAf LFO2 RATE CONTROL CAf LFO2 PITCH DEPTH CAf LFO2 TVF DEPTH CAf LFO2 TVA DEPTH PAf PITCH CONTROL PAf TVF CUTOFF CONTROL PAf AMPLITUDE CONTROL PAf LFO1 RATE CONTROL PAf LFO1 PITCH DEPTH PAf LFO1 TVF DEPTH PAf LFO1 TVA DEPTH PAf LFO2 RATE CONTROL PAf LFO2 PITCH DEPTH PAf LFO2 TVF DEPTH PAf LFO2 TVA DEPTH CC1 PITCH CONTROL CC1 TVF CUTOFF CONTROL CC1 AMPLITUDE CONTROL CC1 LFO1 RATE CONTROL CC1 LFO1 PITCH DEPTH CC1 LFO1 TVF DEPTH CC1 LFO1 TVA DEPTH CC1 LFO2 RATE CONTROL CC1 LFO2 PITCH DEPTH CC1 LFO2 TVF DEPTH CC1 LFO2 TVA DEPTH CC2 PITCH CONTROLCC2 TVF CUTOFF CONTROL CC2 AMPLITUDE CONTROL CC2 LFO1 RATE CONTROL CC2 LFO1 PITCH DEPTH CC2 LFO1 TVF DEPTH CC2 LFO1 TVA DEPTH CC2 LFO2 RATE CONTROL CC2 LFO2 PITCH DEPTH CC2 LFO2 TVF DEPTH CC2 LFO2 TVA DEPTH -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] -24 - +24 [semitone] -9600 - +9600 [cent] -100. 0 - +100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] -24 - +24 [semitone] -9600 - +9600 [cent] -100. 0 - +100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] 24 - +24 [semitone] -9600 - +9600 [cent] -100. 0 - +100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] -10. 0 - +10. 0 [Hz] 0-600 [cent] 0-2400 [cent] 0-100. 0 [%] 40 00 00 00 40 00 00 00 40 40 40 40 00 00 00 40 00 00 00 40 40 40 40 00 00 00 40 00 00 00 40 40 40 40 00 00 00 40 00 00 00 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [semitones] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [semitones] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [semitones] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] 0 [Hz] 0 [cent] 0 [cent] 0 [%] qDrum Setup Parameters * * m: Map number (0 = MAP1, 1 = MAP2) rr: drum part note number (00H-7FH) Size (H) 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 Data (H) 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-01 00-01 Parameter PLAY NOTE NUMBER LEVEL (= NRPN# 26) ASSIGN GROUP NUMBER PANPOT (= NRPN# 28, except RANDOM) REVERB SEND LEVEL (= NRPN# 29) CHORUS SEND LEVEL (= NRPN# 30) Rx. NOTE ON Description Pitch coarse TVA level Non, 1-127 -64 (RANDOM), -63 (LEFT) - +63 (RIGHT) 0. 0-1. 0 Multiplicand of the part reverb depth 0. 0-1. 0 Multiplicand of the part chorus depth OFF/ON OFF/ON Address (H) 41 m1 rr 41 m2 rr 41 m3 rr 41 m4 rr 41 m5 rr 41 m6 rr 41 m7 rr 41 m8 rr * When the Drum Set is changed, DRUM SETUP PARAMETER values will all be initialized. 12 4. Supplementary material qDecimal and Hexadecimal table In MIDI documentation, data values and addresses/sizes of exclusive messages etc. [. . . ] 40H + 01H + 30H + 02H = 64 + 1 + 48 + 2 = 115 (sum) 115 (sum) / 128 = 0 (quotient) . . . 115 (remainder) checksum = 128 - 115 (remainder) = 13 = 0DH This means that F0 41 10 42 12 40 01 30 02 0D F7 is the message we transmit. qAbout tuning In MIDI, individual Parts are tuned by sending RPN #1 (Master Fine Tuning) to the appropriate MIDI channel. In MIDI, an entire device is tuned by either sending RPN #1 to all MIDI channels being used, or by sending a System Exclusive MASTER TUNE (address 40 00 00H). RPN #1 allows tuning to be specified in steps of approximately 0. 012 cents (to be precise, 100/8192 cent), and System Exclusive MASTER TUNE allows tuning in steps of 0. 1 cent. [. . . ]