User manual ROLAND PR-50 V1.2

[. . . ] 1. 2 Owner's Manual Thank you for your purchase of the PR-50 Realtime Video Presenter. 201b Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (p. 3­4), and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. [. . . ] Clip settings are made in the Parameter Area. Parameters area Setting the Clip Playback Segment This sets the clip's In point and Out point. 1. Click on the clip whose playback segment you want to change in the "Clips" list. Use the time slider in the "Parameters" Area to move the preview cursor to the frames you want to set as the In point and Out point. Preview cursor Current time The current time is indicated beneath the preview cursor. 66 Practical Use of the PR-50 3. You can move the cursor in the following ways. Dragging the Preview Cursor with the Mouse You can play back scrubs by dragging the preview cursor with the mouse (p. 70). Right-click the Time Slider with the Mouse Time slider Context menu A context menu appears, allowing you to shift to the following points. · [Jump to top frame] · [Jump to end frame] · [Jump to in point] · [Jump to out point] Using the Transport Control fig. clip03. eps Transport control · · · · : Return to first frame : Go back 1 frame : Go back 10 frames : Start playback · · · · : Advance to last frame : Advance 1 frame : Advance 10 frames : Stop playback Using the In Point and Out Point Settings Icons fig. clip04. eps Jump to out point Jump to in point · · : Jump to In point : Jump to Out point 67 Practical Use of the PR-50 Using the Keyboard Shortcuts · Shortcut key + [Shift] + []: · Shortcut key + [Shift] + []: · Shortcut key + []: · Shortcut key + []: Go back 10 frames Advance 10 frames Go back 1 frame Advance 1 frame Shortcut key is set in the [Preferences] in Selector. This is set to the [Ctrl] key at the factory. For more detailed information, refer to "System Preferences" (p. 44). Using the Optional DV-7DLC · JOG/Shuttle Dial · · · · · : Return to first frame : Go back 10 frames : Advance 10 frames : Pause : Playback · : Play from In point to Out point · · · : Go back 1 frame : Advance 1 frame : Advance to last frame 4. After deciding on the frame, set the In point or Out point as shown below. · Right-click the time slider fig. clip02. eps Time slider · [Set in point] · [Set out point] Context menu A context menu appears, and you can then make the following settings. Using the In Point and Out Point Settings Icons fig. clip05. eps Out point In point · · · Sets the In point : Sets the Out point : Plays back from the In point to the Out point 68 Practical Use of the PR-50 Using the Optional DV-7DLC · · · : : Sets the In point : Sets the Out point Plays back from the In point to the Out point When you set the In point, the In point is then automatically assigned to each of the clip thumbnails. You can also right-click the time slider with the mouse and select [Set thumbnail frame] to assign the frame that appears at the preview cursor position to each of the clip thumbnails. 5. You can delete the In point and Out point in the following ways. Right-click the Time Slider with the Mouse fig. clip02. eps Time slider · [Delete in/out point] Context menu Using the In Point and Out Point Settings Icons fig. clip06. eps Deletes out point Deletes in point · · : Deletes the In point : Deletes the Out point 69 Practical Use of the PR-50 Setting the In Point and Out Point While Playing the Audio You can set the In point and Out point as the audio is being played. 1. Press with audio. The button changes to fig. clip07. eps in the upper left of the clip parameter Preview Area to switch on scrub playback . When On When Off 3. Drag the time slider. The audio track plays back in accordance with the time slider. When playback is paused, playback of the audio for that frame is looped. 4. Press to switch off scrub playback with audio. The button switches to . Specifying Clip Thumbnails You can specify the thumbnails for clips shown in the palette. 1. Drag the time slider with the mouse to the point where the image you want to specify as the thumbnail appears, then right-click. fig. clip02. eps Time slider Context menu When you select "Set thumbnail frame, " the thumbnail switches to the currently displayed image. 70 Practical Use of the PR-50 Setting Loop Mode for Each Clip You can make separate Loop mode settings for each clip. When this is turned on, each clip plays in accordance with its own Loop Mode setting. You can have the same clip play continuously or play the next clip when the current one is finished. You can also have another specified clip play after the current clip is played back. These functions allow you to program the playback sequence of the clips. The Loop mode settings are enabled when Loop playback is on (p. [. . . ] Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit. For Canada NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. For C. A. US (Proposition 65) WARNING This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead. For the USA DECLARATION OF CONFORMITY Compliance Information Statement Model Name : Type of Equipment : Responsible Party : Address : Telephone : PR-50 Realtaim Video Presemter Roland Systems Group U. S. 425 Sequoia Drive, Suite 114, Bellingham, Washington 98226 (360) 594-4282 When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor in your country as shown below. Information ASIA INDONESIA PT. [. . . ]