User manual ROLAND S-770V2

[. . . ] Refer to "Backing Instrument List" (p. Bank select processing will be suspended until a program change message is received. Not recorded in the sequencer. Modulation (Controller number 1) n = MIDI channel number: kk = note number: vv = note off velocity: * * * Status BnH 2nd byte 01H 3rd byte vvH Only the channels assigned to the backing part can be received. The Velocity Values of Note Off message are ignored. [. . . ] is transmitted over the channel assigned to the drum part. When cross sticks are played on the SNARE pad with the [KIT]-[XSTICK] XStick Switch set to ON, the note number set by means of [INST]-[CONTROL]-[BR MIDI] XStick Note No. is transmitted after the gate time over the channel assigned to the drum part. Transmitted only when the device is in play for pattern in which Note Off is recorded. n = MIDI channel number: mm = Bank number MSB: ll = Bank number LSB: * * * * * Not transmitted when [SETUP]-[MIDI]-[PROG] TX Switch is set to "OFF". When a drum kit is selected, the corresponding bank select (00H 00H) is transmitted. When a percussion set is selected, the corresponding bank select (00H 00H) is transmitted. When instruments are selected for the backing part, bank selects for the respective instruments are sent. Refer to "Backing Instrument List" (p. When a pattern is selected, the corresponding bank select for the instrument in each part is transmitted (except for the drum part). Note On Status 9nH 2nd byte kkH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 01H - 7FH (1 - 127) Modulation (Controller number 1) Status BnH 2nd byte 01H 3rd byte vvH n = MIDI channel number: kk = note number: vv = note on velocity: * n = MIDI channel number: 0H - FH (ch. 1 - ch. 16) vv = Control value: 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to MODULATION, this is transmitted when the hi-hat control pedal is adjusted. When the H-HAT pad is struck, this is transmitted as a pedal position message before Note On. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to GENERAL 1, this is transmitted when the hi-hat control pedal is adjusted. When the H-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1­4 and AUX 1­4 pad rims) is set to GENERAL 1, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " and "Toms CC message" sequencer data recorded to the S-770V2 is transmitted during the performance in accordance with the above settings. n = MIDI channel number: 0H - FH (ch. 1 - 16) mm, ll = the value of the parameter specified by RPN mm = MSB, ll = LSB * * This is transmitted only on the channels which are assigned to the backing part. Refer to the RPN item. * Volume (Controller number 7) Status BnH 2nd byte 07H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) * n = MIDI channel number: vv = Volume: 7 MIDI Implementation General Purpose Controller 2 (Controller number 17) Status BnH 2nd byte 11H 3rd byte vvH Hold 1 (Controller number 64) Status BnH 2nd byte 40H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON n = MIDI channel number: 0H - FH (ch. 1 - ch. 16) vv = Control value: 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to GENERAL 2, this is transmitted when the hi-hat control pedal is adjusted. When the H-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM 1­4 and AUX 1­4 pad rims) is set to GENERAL 2, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " and "Toms CC message" sequencer data recorded to the S-770V2 is transmitted during the performance in accordance with the above settings. n = MIDI channel number: vv = Control value: * * This is transmitted only on the channels which are assigned to the backing part. Transmitted only when the device is in play for pattern in which Hold 1 is recorded. Effect 1 Depth (Reverb Send Level) (Controller number 91) Status BnH 2nd byte 5BH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) * n = MIDI channel number: vv = Reverb send level: * * * * General Purpose Controller 3 (Controller number 18) Status BnH 2nd byte 12H 3rd byte vvH This is transmitted only on the channels which are assigned to the backing part. The backing part reverb send level ([PATTERN]-[PART]-[MIXER]-[REV SND]) is transmitted when set. [. . . ] It is not desirable for performance data (such as Standard MIDI File data) to contain many events with running status as given in . This is because if playback is halted during the song and then rewound or fast-forwarded, the sequencer may not be able to transmit the correct status, and the sound generator will then misinterpret the data. Take care to give each event its own status. It is also necessary that the RPN parameter number setting and the value setting be done in the proper order. [. . . ]