User manual ROLAND SC-88VL

[. . . ] Do not use this product near water -- for example, near a bathtub, washbowl, kitchen sink, in a wet basement, or near a swimming pool, or the like. This product should be used only with a cart or stand that is recommended by the manufacturer. This product, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. [. . . ] Then press EFX TYPE [r], and the User effect will be selected. The "X" symbol of the effect number indicates that this is a User effect. PART INSTRUMENT A01 01x Stereo-EQ LEVEL 100 PAN 0 Chapter 5. Convenient functions 99 s Creating and saving a Patch (User Patch) You can modify the parameter values of Parts A01 and A02 as desired, assign a Patch name, and save it. A Patch saved in this way is referred to as a User Patch. 16 Patches can be saved in the Patch number locations U01 - U16. Patch U16 Patch Name : -USER PATCH16Write Patch U01 Patch Name :-USER PATCH01Patch 128 Patch Name : EPILOGUE Patch 001 Patch Name : RB STRAT Parameters common to all Parts PartB16 Part B16 Load Default Setting Patch Patch Name : -SOUND CanvasParameters common to all Parts Part B16 Part A01 Default Value Default Value Part B16 Part A03 Part A02 Part A01 Instrument Effect Part Parameter etc. Part A03 Default Value Default Value * * All Patch parameters (p. 194) are stored. (List of parameters and procedures, p. 150) However, a distinction between GroupA and B of MIDI channels will not be stored. The MIDI channel will be saved as channel "A**" of Group A Drum set parameters are not stored in a Patch. q Naming a User Patch 1. 3. Press the [ALL] button to make the button indicator light, and use lr INSTRUMENT [l ][r ] to select the Patch whose name you wish to modify. Press [ALL] to load Patch. To cancel without loading, press [MUTE]. r r Simultaneously press PAN [r ] and CHORUS [r ]. The specified character location will blink. PART INSTRUMENT ALL 1 RB STRAT LEVEL 100 PAN 0 4. 5. lr Use PART [l ][r ] to move the selected character location. The blinking area will move. lr Press INSTRUMENT [l ][r ] and the displayed character will change. Select the desired character, and return to step 4. Each time you press [ALL], the character will change case as A a A a. However, be aware that if you change the number, the parameter settings will also change. PART INSTRUMENT SET 066*SER DRUM2 LEVEL 100 PAN 0 5. r r Simultaneously press PAN [r ] and CHORUS [r ] to end the procedure. * To store the name of the User Drum Set in memory, follow the steps explained in "Storing an entire Drum Set (procedure 2)" on p. 103, 105. 1 ALL 3 PART INSTRUMENT 4 LEVEL PAN REVERB CHORUS MUTE SC-55 MAP SC-88 MAP 25 KEY SHIFT MIDI CH DELAY 102 Chapter 5. Convenient functions q Storing a Drum instrument 1. Select a Drum Part and Drum Set, and create a drum instrument ("Drum editing procedure" p. 42). PART INSTRUMENT AD1 001 LEVEL C#3 CrshCym1 100 PAN 0 If the above screen is displayed after you create a drum instrument, you can use the following procedure to save your data as a User Drum Set. If the screen display is different than the one shown above, use following procedure 2, 3. 2. 3. Make sure that the [ALL] indicator is dark. If it is lit, press [ALL] to turn it off. l Simultaneously press [SELECT] and EFX TYPE [l ]. The display will show the Part Group (p. 23), Part Mode (p. 27), Drum Set number, Note name, and Drum Instrument name (p. 43). Part Group Part Mode Drum set number PART INSTRUMENT AD1 001 LEVEL C#3 Note Name CrshCym1 Drum Instrument name 100 PAN 0 VIB RATE USER INST SELECT ATTACK VIB DEPTH CUTOFF DECAY VIB DELAY RESONANCE RELEASE EFX ON/OFF EFX TYPE EFX PARAM EFX VALUE 3 Chapter 5. Convenient functions 103 There are two ways to store an edited drum instrument. The first is to store each Drum Instrument individually (procedure 1). The second is to store an entire set of Drum Instruments as a Drum Set (procedure 2). Storing an individual Drum Instrument (procedure 1) The following procedure will store an individual Drum Instrument into the Note Name you specify. 4-1. To store an individual Drum Instrument, simultaneously press the [USER INST] and [SELECT] buttons. Note name PART INSTRUMENT User Drum Set number AD1 Write UD D#3/65? LEVEL 100 PAN 0 Use the INSTRUMENT [l] [r] buttons to specify the Note Name and the User Drum Set number (65/66) into which the data will be stored. When you simultaneously press the INSTRUMENT [l] [r] buttons, the cursor will move between the Note Name and the Drum Set number. 5. To store the data, press [ALL]. To quit without storing, press [MUTE]. Procedure 1 Native/SC-88 Map C3 48 49 50 51 52 53 55 56 57 58 59 C4 60 61 62 63 64 65 67 68 69 70 B4 71 69 70 71 66 62 63 64 65 67 68 66 57 58 59 C4 60 61 54 50 51 52 53 55 56 54 C3 48 49 Procedure 2 Native/SC-88 Map Note name Note number 65 66 65 66 User Drun Set number User Drun Set number 104 Chapter 5. Convenient functions Storing an entire Drum Set (procedure 2) The following procedure will store all the Drum Instruments for the entire currently selected Drum Set. lr 4-2. To store the entire Drum Set, simultaneously press EFX VALUE [l ] [r ] buttons. The User Drum set number into which the data will be stored PART INSTRUMENT AD1 Write U. DRUM 65? LEVEL 100 PAN 0 Use the INSTRUMENT [l] [r] buttons to specify the User Drum Set number (65/66) into which the data will be stored. 5. To store the data, press [ALL]. To quit without storing, press [MUTE]. 5 PART ALL LEVEL MUTE REVERB SC-55 MAP SC-88 MAP DELAY 4-1, 4-2 INSTRUMENT PAN CHORUS KEY SHIFT MIDI CH VIB RATE USER INST SELECT ATTACK VIB DEPTH CUTOFF DECAY VIB DELAY RESONANCE RELEASE EFX ON/OFF EFX TYPE EFX PARAM EFX VALUE 4-1 4-2 Chapter 5. Convenient functions 105 s Copying or Exchanging settings between Parts / Initializing Part settings The settings of the selected Part can be copied to another Part or initialized, and you can exchange settings between parts. [. . . ] Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090 TURKEY ZUHAL DIS TICARET A. S. No. 37 Beyoglu - Istanbul / TURKEY TEL: (0212) 249 85 10 ASIA CHINA Roland Shanghai Electronics Co. , Ltd. No. 1500 Pingliang Road Shanghai 200090, CHINA TEL: (021) 5580-0800 Roland Shanghai Electronics Co. , Ltd. No. 18 3 Section Anhuaxili Chaoyang District Beijing 100011 CHINA TEL: (010) 6426-5050 Roland Shanghai Electronics Co. , Ltd. [. . . ]