User manual ROLAND SR-JV80-02

[. . . ] * * Only the channel assigned to the backing part can be received. Not recorded in the sequencer. n = MIDI channel number: kk = note number: vv = note off velocity: * * * Only the channel assigned to the backing part can be received. The Velocity Values of Note Off message are ignored. When recording, this is recorded in the sequencer data itself. On the normal mode of SR-JV80-02, RPN can be used to modify the following parameters. [. . . ] When a song is selected, the pitch bend sensitivity of the sequencer song data will be transmitted. Regarding the RPN please refer to page 2. Universal Non-realtime System Exclusive Messages Identity Reply Status F0H Data byte 7EH, dev, 06H, 02H, 41H, 3FH, 01H, 00H, 00H, 01H, 02H, 00H, 00H Status F7H Values for the RPN parameter, on the normal mode of SR-JV80-02, are as follows. Regarding the value of each parameter, refer to Data Entry (Controller number 6). RPN mm 00H 7FH ll 00H 7FH Parameter Pitch Bend Sensitivity RPN null Program Change Status CnH 2nd byte ppH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (prog. 1 - prog. 128) n = MIDI channel number: pp = Program number: * * Byte F0H 7EH dev 06H 02H 41H 3FH 01H 00H 00H 01H 02H 00H 00H F7H * Explanation Exclusive status ID number (universal non-realtime message) Device ID (dev: 00H - 1FH (1 - 32) Initial value is 10H (17)) Identity Reply ID number (Roland) Device family code Device family number code software revision level EOX (End Of Exclusive) Not transmitted when SETUP/MIDI COMMON/Tx PC Sw is set to "OFF". (Initial Value is ON) Program changes corresponding to drum kit are sent when drum kits are selected. When Identity Request (page 3) is received, Identity Reply message will be transmitted. 5 MIDI Implementation Data Transmission Data set 1 DT1 (12H) Status F0H Data byte 41H, dev, 00H, 3FH, 12H, aaH, bbH, ccH, ddH, eeH, . . . ffH, sum Status F7H Control Change Modulation (Controller number 1) Status BnH 2nd byte 01H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Byte F0H 41H dev 00H 3FH 12H aaH bbH ccH ddH eeH : ffH sum F7H * Explanation Exclusive status ID number (Roland) Device ID (dev: 00H - 1FH (1 - 32) Initial value is 10H (17)) Model ID (SR-JV80-02) Command ID (DT1) Address MSB: upper byte of the starting address of the data to be sent. Address 2nd: 2nd byte of the starting address of the data to be sent. Address 3rd: 3rd byte of the starting address of the data to be sent. Address LSB: lower byte of the starting address of the data to be sent. Multiple bytes of data are transmitted in order starting from the address. : Data Checksum EOX (End Of Exclusive) n = MIDI channel number: vv = Modulation depth: * In the rhythm part (ch. 10), ignored this message. Data Entry (Controller number 6, 38) Status BnH BnH 2nd byte 06H 26H 3rd byte mmH llH n = MIDI channel number: 0H - FH (ch. 1 - ch. 16) mm, ll = The value of the parameter specified by RPN. While monitoring, if the interval between messages exceeds about 420 ms, the same processing will be carried out as when All Sounds Off, All Notes Off and Reset All Controllers are received, and message interval monitoring will be halted. Channel Pressure Status DnH 2nd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) System Exclusive Message * Regarding the system exclusive message refer to page 3. The System Exclusive Messages received by the normal mode of SR-JV80-02 are; Universal Non-realtime System Exclusive Messages, Universal realtime System Exclusive Messages, Data Requests (RQ1), and Data Set (DT1). n = MIDI channel number: vv = Channel pressure: * * When channel pressure is received, the effect selected for channel pressure, in global parameter control (page 8), is applied. In the rhythm part (ch. 10), ignored this message. Pitch Bend Change Status EnH 2nd byte llH 3rd byte mmH 0H - FH (ch. 1 - ch. 16) 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191) n = MIDI channel number: mm, ll = Pitch Bend value: * In the rhythm part (ch. 10), ignored this message. 7 MIDI Implementation System exclusive messages related to mode setting Turn General MIDI System On This is a command message that resets the internal settings of the unit to the General MIDI initial state (General MIDI System - Level 1). After receiving this message, this unit will automatically be set to the proper condition for correctly playing a General MIDI score. Status F0H Byte F0H 7EH 7FH 09H 01H F7H * * Data byte 7EH, 7FH, 09H, 01H Status F7H rr=00H-7FH pp=4 rr=00H-7FH pp=5 rr=00H-7FH * * 0 - 600 cents LFO Filter Depth 0 - 2400 cents LFO Amplitude Depth 0 - 100 % Even if the Device ID is 7FH (Broadcast), Identity Reply message will be transmitted. In the rhythm part (ch. 10), ignored this message. Data transmission Request data 1 RQ1 (11H) * Regarding the RQ1 refer to page 3. Explanation Exclusive status ID number (Universal Non-realtime Message) Device ID (Broadcast) Sub ID#1 (General MIDI Message) Sub ID#2 (General MIDI On) EOX (End Of Exclusive) Data set 1 DT1 (12H) * Regarding the DT1 refer to page 4. Section 2. Transmit data * When SETUP/MIDI COMMON/Soft Thru is set to "ON", messages received in addition to the following messages are also sent. Not Received when SETUP/MIDI COMMON/Rx GM ON is set to "OFF". (Initial Value is ON) There must be an interval of at least 50 ms between this message and the next. Turn General MIDI System Off When a "GM System Off" is received, the SR-JV80-02 is switched to normal mode. Status F0H Byte F0H 7EH 7FH 09H 02H F7H * * Data byte 7EH, 7FH, 09H, 02H Status F7H System Realtime Messages Active sensing Status FEH * This will be transmitted constantly at intervals of approximately 250 ms. Explanation Exclusive status ID number (Universal Non-realtime Message) Device ID (Broadcast) Sub ID#1 (General MIDI Message) Sub ID#2 (General MIDI Off) EOX (End Of Exclusive) System Exclusive Messages Universal Non-realtime System Exclusive Messages Identity Reply * Regarding the Identity Reply refer to page 5. Not Received when SETUP/MIDI COMMON/Rx GM ON is set to "OFF". (Initial Value is ON) There must be an interval of at least 50 ms between this message and the next. Universal Non-realtime System Exclusive Messages Identity Request * Regarding the Identity Request refer to page 3. Data Transmission Data set 1 DT1 (12H) * Regarding the DT1 refer to page 4. Global Parameter Control Channel Pressure Status F0H Byte F0H 7FH dev 09H 01H 0nH ppH rrH F7H pp=0 rr=28H-58H pp=1 rr=00H-7FH pp=2 rr=00H-7FH pp=3 Data byte 7FH, dev, 09H, 01H, 0nH, ppH, rrH Status F7H Explanation Exclusive status ID number (Universal Realtime Message) Device ID (dev: 00H - 1FH Initial value is 10H (17)) Sub ID#1 (Controller Destination Setting) Sub ID#2 (Channel Pressure) MIDI channel (00H - 0FH) parameter range EOX (End Of Exclusive) Pitch Control -24 - +24 semitones Filter Cutoff Control -9600 - +9450 cents Amplitude Control 0 - 200 % LFO Pitch Depth 8 MIDI Implementation Parameter address map (Model ID = 00H 3FH) This map indicates address, size, Data (range), Parameter, and Description of parameters which can be transferred using "Data set 1 (DT1)". All the numbers of address, size, Data, and Default Value are indicated in 7-bit Hexadecimal-form. [. . . ] checksum F7 (6) In other words, the above messages specify a value of 0C 00H for RPN parameter number 00 00H on MIDI channel 4, and then set the RPN parameter number to 7F 7FH. RPN parameter number 00 00H is Pitch Bend Sensitivity, and the MSB of the value indicates semitone units, so a value of 0CH = 12 sets the maximum pitch bend range to +- 12 semitones (1 octave). (On GS sound sources the LSB of Pitch Bend Sensitivity is ignored, but the LSB should be transmitted anyway (with a value of 0) so that operation will be correct on any device. ) Once the parameter number has been specified for RPN or NRPN, all Data Entry messages transmitted on that same channel will be valid, so after the desired value has been transmitted, it is a good idea to set the parameter number to 7F 7FH to prevent accidents. This is the reason for the (B3) 64 7F (B3) 65 7F at the end. [. . . ]