User manual ROLAND TD-12 V1.00 MIDI IMPLEMENTATION

[. . . ] TD-12 MIDI Implementation Model: TD-12 Date: Dec. 17, 2004 Version: 1. 00 Control Change Bank Select (Controller number 0, 32) Status BnH BnH 2nd byte 00H 20H 3rd byte mmH llH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (bank. 1 - bank. 128) processed as 00H 1. Receive data Channel Voice Messages * * Following Channel Voice Messages can be received in [SETUP]-[MIDI]-[MIDI CH] Tx/Rx Channel. Not received when [SETUP]-[MIDI]-[MIDI CH] Rx/Rx Switch is set to "OFF. n = MIDI channel number: mm = Bank number MSB: ll = Bank number LSB: * * Note Off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) * Only the channels assigned to the backing part can be received. [. . . ] When cross sticks are played on the SNARE pad with the [KIT]-[XSTICK] XStick Switch set to ON, the note number set by means of [INST]-[CONTROL]-[BR MIDI] XStick Note No. is transmitted over the channel assigned to the drum part. In the channel assigned to the durm part, the note number transmitted when the hi-hat pad is srtuck (open, closed) switches with the value set with [SETUP]- * * * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to MODULATION, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to MODULATION, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. 6 TD-12 MIDI Implementation Breath Controller (Controller number 2) Status BnH 2nd byte 02H 3rd byte vvH 0H - FH (ch. 1 - 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow * * The part volume ([PATTERN]-[PART]-[MIXER]-[VOLUME]) information is transmitted when set. The volume of each part in a pattern is transmitted when the pattern is selected (except for the drum part). n = MIDI channel number: vv = Control value: Panpot (Controller number 10) Status BnH 2nd byte 0AH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 40H - 7FH (Left - Center - Right) * * * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to BREATH, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to BREATH, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. n = MIDI channel number: vv = Panpot: * * * This is transmitted only on the channels which are assigned to the backing part. The backing part pan ([PATTERN]-[PART]-[MIXER]-[PAN]) information is transmitted when set. The backing part pan is transmitted when the pattern is selected. Expression (Controller number 11) Status BnH 2nd byte 0BH 3rd byte vvH 0H - FH (ch. 1 - 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow Foot Controller (Controller number 4) Status BnH 2nd byte 04H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow n = MIDI channel number: vv = Control value: n = MIDI channel number: vv = Control value: * * * * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to FOOT, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to FOOT, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. * * This is transmitted only on the channel which is assigned to the drum part. When [SETUP]-[MIDI]-[CTRL] Pedal CC is set to EXPRESSION, this is transmitted when the hi-hat control pedal is adjusted. When the HI-HAT pad is struck, this is transmitted as a pedal position message before Note On. When either [SETUP]-[MIDI]-[CTRL] Snare CC (for the SNARE pad head and rim), Ride CC (for the RIDE pad bow), or Toms CC (for the TOM1-3 and AUX12 pad rims) is set to EXPRESSION, this is transmitted as a striking position message before Note On (when the [INST]-[CONTROL]-[MIDI] Position Ctrl setting is set to ON). "Pedal CC message, " "Snare CC message, " "Ride CC message, " "Toms CC message" sequencer data recorded to the TD-12 is transmitted during the performance in accordance with the above settings. * General Purpose Controller 1 (Controller number 16) Status BnH 2nd byte 10H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Pedal position: open to closed Head strike position: center to perimeter Rim strike position: deep to shallow Data Entry (Controller number 6, 38) Status BnH BnH 2nd byte 06H 26H 3rd byte mmH llH n = MIDI channel number: vv = Control value: n = MIDI channel number: 0H - FH (ch. 1 - 16) mm, ll = the value of the parameter specified by RPN mm = MSB, ll = LSB * * This is transmitted only on the channels which are assigned to the backing part. [. . . ] On some sequencers, events occurring in the same (or consecutive) clock may be transmitted in an order different than the order in which they were received. For this reason it is a good idea to slightly skew the time of each event (about 1 tick for TPQN=96, and about 5 ticks for TPQN=480). * TPQN : Ticks Per Quarter Note <Example 1> What is the decimal expression of 5AH ?From the preceding table, 5AH = 90 <Example 2> What is the decimal expression of the value 12 34H given as hexadecimal for each 7 bits? [. . . ]