User manual ROLAND TD-20K

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the TD-20K Roland Drum System. Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. [. . . ] Tighten `e' and `f' in the same way. Refer to "Adjusting the Head Tension" above. * Fully tightening a tuning bolt at only a single location produces uneven tensioning, which may make it impossible to obtain the proper strike sensitivity and may even result in incorrect operation. Be sure to tighten each tuning bolt a little at a time, as described in the above explanation. 10 PD-125/PD-105 (V-Pad) Component (Parts) Names Head Stand fixing screw Hoop (rim) Tuning bolts fig. 15. e The only difference between the PD-125 and the PD-105 is the diameter. * The figure shows the PD-125. Lugs Bracket Shell Output jack Frame * Do not apply excessive force to the sensor located below the center of the head of the unit. Doing so can interfere with accurate detection, and may damage it. * Due to the nature of the materials used in the sensor, changes in room temperature and humid may affect the sensitivity of the sensor. Setup Connecting to the Sound Module Use the internal stereo cable to connect to the MDS-20 drum stand. If you use a monaural cable, rim shots cannot be played. You can play rim shots when the pad is connected to the trigger input shown below. To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. Rim-Shot-Capable Trigger Inputs 2 (SNARE), 3­6 (TOM 1­4), 12­15 (AUX 1­4) Brush-Sweep-Capable Trigger Inputs 2 (SNARE) Mounting on a Snare Stand Make sure the snare drum stand you use is designed to firmly hold a 12-inch (PD-125) drum. Be sure to tighten the stand fixing screw to prevent the noise. Mounting on a Tom Stand fig. 16. e When mounting the PD-125/105 to a tom stand, verify the dimension of the rod. (6. 3­12. 5 mm) loosen tighten Rod (diameters which can be attached: 6. 3­12. 5 mm) 11 Adjusting the Head Adjusting the Head Tension When adjusting, use the included tuning key. PD-125/PD-105 (V-Pad) On the PD-125/105, adjusting the head tension affects only the head response, and not the pitch of the sound, as it would on an acoustic drum. To adjust the pitch, edit the sound parameters of the TD-20. For details refer to the owner's manual. Heads MUST BE TUNED BEFORE PLAYING. Like with an acoustic drum, accurate and equal head tension is needed for correct triggering response. * Head tension that is too loose may not only cause incorrect operation, but may even damage the sensor. 1. Loosen the tuning bolts until a slight gap is produced. Tighten all tuning bolts by fingers, as tightly as you can. Head tension may change over a period of time, so readjust when necessary. fig. 17. e Tuning bolt Washer Slight gap Hoop 3. Using the tuning key, turn the tuning bolts two full revolutions each, thus tightening them. Tighten each tuning bolt one by one, observing the numerical order shown in the figure. fig. 18 1 3 HEAD MADE BY REMO U. S. A. 5 6 4 2 12 CY-15R/CY-14C (V-Cymbal Ride/Crash) Contents of the Package CY-15R (Ride) CY-15R unit Wing nut Felt washer Stopper Cable tie CY-14C (Crash) CY-14C unit Wing nut Felt washer Stopper Cable tie Component (Parts) Names CY-15R (Ride) fig. 19. e Wing Nut Felt Washer Stopper Bell Portion Bow Portion Edge Portion Diameter: 15 inches BOW/EDGE OUTPUT Jack BOW/BELL OUTPUT Jack CY-14C (Crash) fig. 20. e Wing Nut Felt Washer Stopper Bow Portion Edge Portion Diameter: 14 inches BOW/EDGE OUTPUT Jack * The CY-14C has no BOW/BELL OUTPUT Jack. 13 Mounting on the Stand CY-15R/CY-14C (V-Cymbal Ride/Crash) 1. Use the included tuning key to tighten the stopper bolt. The stopper keeps the V-Cymbal from turning, and prevents the cables from catching or getting tangled on the stand. fig. 21. e Stopper (Be sure to orient it correctly) Tighten the bolt with a commercially available drum key 2. Position the Roland logo on the farther side, as viewed from the performer. Tighten the felt washer and the wing nut to obtain the desired movement. fig. 22. e Wing Nut Position the Roland logo on the opposite side of the playing area Felt Washer 4. Secure the cables in place with the cable tie, while leaving some slack in the cables to ensure that they are not pulled by the movement of the cymbal units when struck. fig. 23. e Leave some slack in the cable(s) Wind the cable tie twice Tighten it not to slip Turn back to fix the cable(s) * Take care to ensure that the cables do not touch the cymbal units and/or the stand. A cable touching a cymbal unit or a stand may cause double sounding or other incorrect operation. * Double sounding may occur if the wing nut is loose. [. . . ] Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090 BRAZIL Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666 UNITED KINGDOM Roland (U. K. ) Ltd. Atlantic Close, Swansea Enterprise Park, SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 702701 PANAMA SUPRO MUNDIAL, S. A. Boulevard Andrews, Albrook, Panama City, REP. [. . . ]