User manual ROLAND V-44SW

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (p. 6­7), and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. [. . . ] System" and select "1: System Frame Rate" from the sub-menu. Set each parameter to "60-NTSC" or "50-PAL. " 60-NTSC: NTSC format 50-PAL: PAL format Off 75% Color Bar 100% Color Bar 35 Switching Video Selecting the Video Switching Mode The V-44SW features two different video switching modes, "Direct mode" and "Preset mode. " Each mode functions in switching video as follows. Switching Video in Direct Mode Immediately after the power is turned on, SD VIDEO Channel 1 is assigned as the final output. 1 Press one of the SD VIDEO buttons [1]­[4] or one of the HD/RGB buttons [1]­[4] to select the channel. The selected button lights up, and the final output video is switched. Lit Direct Mode The final output video is switched when channels are selected with the press of a single button. Final Output Video Preset Mode When a channel is selected, the video in the preview monitor switches. Pressing the [TAKE] button confirms selection of this as the output video, switching the final output video. Preview Final Output Video Selecting an HD/RGB channel to which no signals are input may result in delayed switching of the video. About the Indicators Whenever video is being input to a channel, its indicator lights up. You can determine the type of video signal being input by observing the color of the indicator. Indicator Lit (Red) Lit (Green) Off SD VIDEO1­4 Composite signal S-video signal No signal input HD/RGB1­4 RGB signal Component signal No signal input Selecting the Video Switching Mode 1 2 3 Press the [MENU] button to display the Main menu. System" and select "7: Panel Operation Mode" from the sub-menu. Select "Direct Mode" or "Preset Mode. " Direct Mode:video is switched in Direct mode. Preset Mode:video is switched in Preset mode. About the Colors of Channel Select Buttons You can change the colors in which channel select buttons light. 1 2 3 Press the [MENU] button to display the Main menu. System" and select "8: Input Sw LED Color" from the sub-menu. Select the colors for the channel select buttons. About the Effects Used in Switching Screens You can apply the screen transition effects, regardless of the mode used for switching the video. For more detailed instructions, refer to "Selecting the Effects To Be Applied in Switching" (p. 38). "Sub" refers to the colors in which LEDs light when video is selected in the Picture in Picture sub-screen (p. 39) and with the key composite effects (p. Value Main=YEL Main=YEL Main=RED Main=RED Main=GRN Main=GRN : : : : : : Sub=GRN Sub=RED Sub=GRN Sub=YEL Sub=RED Sub=YEL Main Yellow Yellow Red Red Green Green Color Sub Green Red Green Yellow Red Yellow 36 Switching Video Switching in Preset Mode Immediately after the power is turned on, SD VIDEO Channel 1 is assigned as the final output. To Prevent Errors in Using the Channel Select Buttons You can disable the operation of channel select buttons you are not using. This is useful in preventing accidental output of video. 1 Press one of the SD VIDEO buttons [1]­[4] or one of the HD/RGB buttons [1]­[4] to select the channel. The selected button flashes, and the input video appears in the preview monitor connected to the HD/RGB OUT PREVIEW connector. SD VIDEO Buttons [1]­[4] The final output video is not switched at this stage. Select the video you want to use as the final output while checking the video being input. The channel select button corresponding to the previewed video flashes. Flashing 1 2 Press the [MENU] button to display the Main menu. SD Input" and select "1: SD Ch1" ­ "4: SD Ch4" from the sub-menu to specify the channel you want to set. Select "6: SD Sw Enable" from the SD Ch submenu. Set this to "Off. " Once set, the button will not function even when pressed. 3 4 Selecting an HD/RGB channel to which no signals are input may result in delayed switching of the video. HD/RGB Buttons [1]­[4] 2 Once you decide to use the video, press the [TAKE] button. [. . . ] Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit. For Canada NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. For the USA DECLARATION OF CONFORMITY Compliance Information Statement Model Name : Type of Equipment : Responsible Party : Address : Telephone : V-44SW MULTI-FORMAT VIDEO SWITCHER Roland Systems Group U. S. 425 Sequoia Drive Suite 114, Bellingham, Washington, 98226 USA (360) 594-4282 For EU Countries When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor in your country as shown below. Information ASIA INDONESIA PT. 15J-15O Jakarta Pusat INDONESIA TEL: (021) 632-4170 CENTRAL/LATIN AMERICA BRAZIL Roland Brasil Ltda. [. . . ]