User manual ROLAND VS-880V2

[. . . ] The user's guide should be saved and kept on hand as a convenient reference. Copyright © 2000 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Visit the Roland US Web Site at http://www. rolandus. com CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] You don't have to figure out where the ticking should begin in order to have the FROM and the TO points line up. fig. 04-05 Steps for Track Editing There are two basic editing steps on the VS-880V2: Step 1: Step 2: Set the edit points. Complete the button presses to perform the edit. Example3: Copying using the "FROM" setting C As you approach the editing process, certain information is necessary to perform the edit. You should determine: · What kind of edit you want to do (Erase, Copy, Insert, etc. --see Chapter 10) · Which track or tracks you want to edit (one, several, or all) · Where the edit points are (Start, End, From, To) Simple edits such as Track Erase and Track Cut only have two edit values: START and END. Edits such as Track Move and Track Copy have two additional values: FROM and TO. These terms are explained here: START (Start point) Specifies the starting time of the audio to be edited. END (End Point) Specifies the ending time of the audio to be edited. Start From End To C' Time Step 1: Set the Edit Points The first step to editing audio on the VS-880V2 is finding the START and END edit points. These edit points indicate where on the track you want to start the edit, and where on the track you want to end the edit. There are many different ways to do this, and many different tools available to help you, including locators, Preview and Scrub. Chapter 11 157 Chapter 11 Editing Tips & Tools Here are some common ways to set edit points: · Create locators while the song is playing · Use [FF] and [REW] to locate to point you want to edit · Preview To and Preview From · Scrub Typically, you will use a combination of the above methods to define edit points. For example, as you're listening to your song, you may press a LOCATOR button to establish a point close to where an edit needs to occur. Now that you're in the ballpark, you might use Preview and Scrub to define a precise edit point. Now try the edit: 1. If you don't see "Erase" above [F2], press [PAGE] until "Erase" appears, and then press [F2 (Erase)]. For locating precise points in a song, Preview offers a way to hear a short portion of audio leading up to the current time location, just after the current time location, or just before and after the current time location. 158 Chapter 11 Editing Tips & Tools Preview [TO], [THRU], and [FROM] Preview provides a fast and convenient method to audition a short portion of a track. You can specify the length of the audition from 1 to 10 seconds. Press the appropriate Preview button [TO], [THRU], or [FROM] when the song is stopped. [TO]: A preview of the song is played back one time for the specified duration. If the Preview To value is set at two seconds, you will hear two seconds of the song leading up to the point of the current play position. You will hear two seconds of audio playing up to the current timeline. Use [TO] when you are trying to determine the exact location of the beginning of a sound, for example the beginning of a snare hit, or the start of a vocal track. [THRU]: A preview of the song is played back one time for the specified duration. Based on the Preview Lengths for both the Preview To and Preview From, you will hear a portion of the song playing through the current position of the timeline. Use [THRU] when you are trying to determine the transition between two tracks, and you want to hear how one ends and the other begins. [FROM]: A preview of the song is played back one time for the specified duration. [. . . ] Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. ADVARSEL Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruks joner. VAROITUS Paristo voi räjähtää, jos se on virheellisesti asennettu. [. . . ]