User manual ROLAND XV-5050 MANUAL 2

[. . . ] OWNER'S MANUAL Thank you, and congratulations on your choice of the Roland XV-5050. Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (pp. 3­4), and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. [. . . ] Adjusts the amount of the delay sound that's fed back into the effect. Adjusts the frequency above which sound fed back to the effect is filtered out. If you do not want to filter out any the high frequencies, set this parameter to BYPASS. Adjusts the volume balance between the sound sent through the delay (W) and the sound that's not sent through the delay (D). Output level Parameter Cho Delay Cho Rate Cho Depth Cho Balance # Flg Rate Flg Depth Flg Feedback Value 0. 0-100. 0 ms 0. 05-10. 00 Hz 0-127 D100:0WD0:100W 0. 05-10. 00 Hz 0-127 -98-+98 % Description Adjusts the time until the chorus is heard. Modulation frequency of the chorus effect Modulation depth of the chorus effect Volume balance between the direct sound (D) and the chorus sound (W) Modulation frequency of the flanger effect Modulation depth of the flanger effect Adjusts the amount of the flanger sound that's fed back into the effect. Adjusts the time until the flanger sound is heard. Adjusts the volume balance between the sound sent through the flanger (W) and the sound that's not sent through the flanger (D). Output level Delay Time Dly Feedback Dly HF Damp 200-8000 Hz, BYPASS Flg Delay Flg Balance # 0. 0-100. 0 ms D100:0WD0:100W Dly Balance # D100:0WD0:100W Level 0-127 Level 0-127 38: CHORUS/DELAY The parameters are the same as for "35: CHORUS -> DELAY. " However, the Delay Balance parameter adjusts the volume balance between the direct sound and the delay sound. fig. 02-038m 36: FLG -> DELAY fig. 02-036m Balance D L in Feedback Balance D Balance W Balance W L out L in Balance W Balance D L out Chorus Balance W Flanger R in Balance D Delay Balance W Feedback Feedback R out Balance D Delay R in Balance D Balance W Parameter Flg Rate Flg Depth Flg Feedback Value 0. 05-10. 00 Hz 0-127 -98-+98 % Description Frequency of modulation Depth of modulation Adjusts the amount of the flanger sound that's fed back into the effect. Adjusts the time until the flanger is heard. Volume balance between the direct sound (D) and the flanger sound (W) Adjusts the time until the delay sound is heard. Adjusts the amount of the delay sound that's fed back into the effect. Adjusts the frequency above which sound fed back to the effect is filtered out. If you do not want to filter out any high frequencies, set this parameter to BYPASS. Adjusts the volume balance between the sound sent through the delay (W) and the sound that's not sent through the delay (D). Output level R out 39: FLG/DELAY The parameters are the same as for "36: FLG -> DELAY. " However, the Delay Balance parameter adjusts the volume balance between the direct sound and the delay sound. fig. 02-039m Flg Delay Flg Balance # 0. 0-100. 0 ms D100:0WD0:100W 0. 0-500. 0 ms -98-+98 % Delay Time Dly Feedback Balance D L in Flanger Feedback Feedback L out Balance W Dly HF Damp 200-8000 Hz, BYPASS Delay R in Balance D Balance W R out Dly Balance # D100:0WD0:100W Level 0-127 84 Chapter 4 Using the XV-5050 Effects 40: CHO/FLANGER The parameters are the same as for "37: CHO -> FLANGER. " However, the Flanger Balance parameter adjusts the volume balance between the direct sound and the flanger sound. fig. 02-040m 42: KEYSYNC FLG (Keysync Flanger) This effect controls the Flanger by resetting the effect at the volume of the sound sent into to the effect, restarting from the same pitch each time the Flanger is reset. This parameter lets your playing dynamics on the keyboard control the flanger effect. fig. 02-042m Balance D L in Chorus Feedback L out Balance W L in Flanger 2-Band EQ L out Flanger R in Balance D Balance W R out Feedback Feedback Flanger 41: St PHASER (Stereo Phaser) This is a stereo phaser. With the Step effects, you can also make stepped changes in the pitch of sounds to which the Phaser effect is applied. fig. 02-041m R in 2-Band EQ Value 0. 05-10. 00 Hz, note *2 0-127 -98-+98 % R out Parameter LFO Rate # LFO Depth Feedback # Description Frequency of modulation Depth of modulation Adjusts the amount of the flanger sound that's fed back into the effect. Spatial spread of the sound Adjusts the time until the flanger is heard. Type of filter OFF: no filter is used LPF: cuts the frequency range above the Cutoff Freq HPF: cuts the frequency range below the Cutoff Freq L in Phaser Mix Mix 2-Band EQ L out Phase Pre Delay 0-180 deg 0. 0-100 ms OFF, LPF, HPF R in Phaser 2-Band EQ R out Filter Type Parameter Type Value 1, 2 Description Type of phaser Type 2 adds more of the phaser effect to the high frequencies than Type 1. Number of stages in the phaser Selects whether the left and right phase of the modulation are the same or opposite each other. INVERSE: The left and right phase are opposite. When using a mono source, this spreads the sound in stereo. [. . . ] Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051 BRAZIL Roland Brasil Ltda Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666 GERMANY Roland Elektronische Musikinstrumente HmbH. Oststrasse 96, 22844 Norderstedt, GERMANY TEL: (040) 52 60090 INDONESIA PT Citra IntiRama J1. 15J-150 Jakarta Pusat INDONESIA TEL: (021) 6324170 COSTA RICA JUAN Bansbach Instrumentos Musicales Ave. 1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211 MIDDLE EAST BAHRAIN Moon Stores No. 16, Bab Al Bahrain Avenue, P. O. Box 247, Manama 304, State of BAHRAIN TEL: 211 005 Roland Canada Music Ltd. [. . . ]