User manual ROLLS MP1288

[. . . ] This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. MP1288 MIDIWIZARD MIDI CONTROLLER RFX Salt Lake City, UT 5/98 OWNERS MANUAL INTRODUCTION Thank you for purchasing the MP1288 MIDIWIZARD. The MP1288 was designed to give you control of a whole universe of MIDI-compatible processors, keyboards, sequencers, MIDI-linked PC terminals or anything else than can receive MIDI on any of the 16 standard MIDI channels. The MIDI WIZARDS's compact, durable chassis and low profile make it easily integrated into the sometimes crowded studio or stage environment. And, if you choose not to use it as a foot controller, the Wizard is designed to fit into an extra rack space in any 19 inch audio rack. [. . . ] MIDI TEST MODE The 1288 comes with a bonus testing mode for testing other MIDI transmitters. To access the TEST Mode, hold the two PROGRAM buttons down on power-up. Connect the unit to be tested to the MIDI IN jack of the 1288, and send a signal from the test unit. The MIDI WIZARD will display the channel and the program change number (MPC#) coming in from the unit being tested. If a controller is being tested, the display will show the channel number, then the controller number while lighting the CONTROLLER # LED. In this mode, all the buttons on the MP1288 are inactive because the 1288 is only an input testing device. This features makes the MP1288 a very useful tool when troubleshooting any MIDI transmitting device. TO EXIT MIDI TEST MODE YOU MUST UNPLUG THE POWER FROM THE MP1288. DESCRIPTION A B C MIDI IN D MIDI OUT E POWER 1 2 3 4 5 6 7 8 F CONTINUOUS CONTROLLERS ID IW IZ A R D PROGRAM MP1288 CONTROLLER # CHANNEL # RUN MAP # LEARN SEND MPC# MADE IN USA 0 5 CHANNEL 1 6 MAP # 2 7 MPC # 3 8 CONTROLLER # 4 9 STORE PROGRAM CHANNEL MAP # MPC # CONTROLLER # MODE 0 - 127 1 - 128 G A: Continuous Controller input jacks. 1/4" jacks (tip-sleeve only) for receiving 0-5 volt continuous controller voltages, or standard resistive volume pedal outputs. B: 3-digit high-efficiency number display for: · Displaying the program number being accessed while in normal SEND mode. · Displaying MAP numbers, MIDI channel numbers, and CONTINUOUS CONTROLLER numbers being assigned while in LEARN mode. 5-pin jack for connection to the MIDI device to be controlled. For connection to the 12 VAC or DC supply. Indicate the following: · The SEND LED indicates that a MIDI signal being sent to the unit(s) being controlled. · The RUN LED indicates the unit is in "send" mode. · The LEARN LED indicates the unit is in "learn" mode. · As you assign each MAP #, CHANNEL #, MIDI PROGRAM CHANGE (MPC) #, or CONTROLLER #, the corresponding LED will stay lit. For performing the following functions: · Incrementing, decrementing, and programming Program #s, MIDI Channel #s, MIDI Map #s, MPC #s, Continuous Controller #s, and MODEs. · STOREs and directly accesses program #s. OPERATION DEFINITION OF TERMS In order for you to clearly understand programming and operating your MP1288, youmust u nderstand the following terms: Program - Refers to the MP1288 Program Number, the number displayed on the 1288. Preset (or Program Change Number), refers to the MIDI number sent by the MP1288. MAP or PATCH refers to Program Changes (up to 8 total) sent by one Program of 2 5 MIDI Channel - Refers to the specific channel the MIDI data is being transmitted and received upon. [. . . ] Press the MPC # Up button and change it to 14. Press the Channel button and change it to 02. Now press and hold the Program Up and Down buttons until the MP1288 returns to Run Mode. In order for all of this to work, your first device (the SM1) must be on MIDI Channel 01, the second device (the SM2) must be on channel 02, and the third device (the DSP1) must be on MIDI channel 03. [. . . ]