User manual ROLLS RM67

[. . . ] This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RM67 Mic/Source Mixer MIC ONE MIC TWO MIC THREE 1 2 3 4 TONE TONE TONE 0 LEVEL 10 clip 0 LEVEL 10 clip 0 LEVEL 10 clip 0 10 0 10 0 10 0 LEVEL LEVEL LEVEL LEVE MICROPHONE INPUTS SOURCE INPUTS 4 MASTER LEVEL MICROPHONE/SOURCE MIXER 0 10 - LEVEL BASS + + TREBLE 0 10 pwr RM67 FEATURES · Three XLR balanced inputs with phantom power · Four stereo Source inputs · Tone controls for each Microphone input · Clip indicators for each Microphone input · Bass and Treble controls for the Source inputs · 1/4" input for remote volume control · RCA Record Out · Master Output Level control · 1/4" TRS balanced outputs ROLLS CORPORATION SALT LAKE CITY, UTAH 11/03 OWNERS MANUAL INTRODUCTION Thank your for your purchase of the Rolls RM67 Microphone/Source Mixer. The RM67 is a single rack space audio mixer with three XLR inputs and four stereo RCA source inputs. Talkover features have been included on Mic 1 and Source 4 for paging and music priority functions. [. . . ] When the control is turned counter-clockwise, the high frequencies are cut, when the control is turned clockwise, the low frequencies are cut. Source 1 - 4: Adjust the volume of input from the RCA Source Inputs. Bass: Adjusts the low frequencies of the Source signals only. Treble: Adjusts the high frequencies of the Source signals only. Master Level: Adjusts the overall volume of the RM67 Main Outputs. pwr: LED indicating power is applied to the RM67 and the unit is on. REAR PANEL PRIORITY SPARE MIC 3 MIC 2 MIC 1 L L MIC INSERT WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE NO USER SERVICABLE PARTS INSIDE. R MUTE RECORD OUT R mic/line mic/line mic/line RISQUE DE CHOC - NE PAS ENLEVER SOURCE INPUTS Mic 1 - 3: XLR inputs for dynamic or condenser microphones, or balanced linelevel signals. Mic/Line Switch: Pads the XLR Mic input by 30 dB when pressed in. DIP SWITCH: Contains the small switches for engaging Mic 1 - 3 phantom power, the priority (Talk Over) functions, and the Mono/Stereo select. MIC INSERT: 1/4" TRS insert jack for adding external processing to the Mic signals. SOURCE INPUTS: Stereo RCA jacks, Channels 1 - 4, for connection to stereo sources such as AM/FM tuners, cassette players, cd players, or video players. RECORD OUT: Stereo RCA jacks, contains all mixed signals before the Remote Volume jack, and Master Level control. MUTE: RCA jack for connection to a tip-to-ground muting circuit. REMOTE VOLUME: 1/4" TS jack for connection to a remote potentiometer for master volume control. 20K Ohm audio taper potentiometer is recommended. MAIN OUTPUTS: 1/4" TRS balanced Right and Left Outputs. 5 2 CONNECTION Connect low impedance microphones to the Mic inputs. If a paging microphone is being used, connect it to Mic Input 1 so it may be used with the Talk Over function. Connect source signals such as CD players, cassette players or video players to the RCA Source Inputs. If a jukebox is being connected, and you want its signal to mute the other source signals, connect it to Source input 4. [. . . ] Connect the Main Right and Left outputs to your power amplifiers. The RM67 output jacks will accommodate balanced or unbalanced connections. For unbalanced operation use 1/4" Tip Sleeve jacks, for balanced operation use 1/4" Tip Ring Sleeve jacks. [. . . ]