User manual ROTEL RX-1050

[. . . ] Owner's Manual RX-1050 AM/FM Stereo Receiver AM/FM STEREO RECEIVER RX-1050 POWER SPEAKER A TUNING BAND TREBLE PHONO CD TUNER TAPE VIDEO 1 PHONES B TUNE/ PRESET MONO MEMORY BASS VIDEO 2 VIDEO 3 VIDEO 4 ZONE REC RX-1050 Surround Sound Receiver Important Safety Instructions WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose the unit to moisture or water. Do not allow foreign objects to get into the enclosure. [. . . ] You will hear this source and, if you have selected a video source, see its picture on your TV monitor. The left side of the front panel display shows the current source selection. The input source buttons can also be used (with described in the next secthe REC button tion) to select an analog input source signal to be available at the outputs for recording. Additionally, the input source buttons can be to select an used with the ZONE button analog input source for ZONE 2. Tuning Controls The RX-1050 features a digital synthesized AM/ FM tuner with 30 station presets. Operation of the tuning functions involves the use of six buttons on the front panel plus the numeric and other buttons on the remote. HEADPHONES Jack This jack accepts a standard 1/4 inch stereo headphone plug. Use an adaptor if your headphones have a small mini-plug. BAND Button TV/BAND Button The BAND button on the front panel and the TV/BAND button on the remote selects AM or FM mode. Press either button to toggle back and forth between the two modes. An indicator at the left portion of the front panel display confirms your choice and the currently tuned station frequency is shown in the main portion of the display. Inserting a headphone plug does not automatically disable all speaker outputs. Use the SPEAKER buttons described in the next section to turn the speakers on or off during headphone listening. NOTE: 13 English DIRECT FREQUENCY/10 Button If you know the frequency of the desired station, you may tune it directly using the DIRECT FREQUENCY/10 button and the NUMERIC on the remote. Press the DIRECT FREQUENCY/10 button to change the NUMERIC buttons from station preset to frequency direct mode. The station frequency in the front panel display change to a series of four bars, representing the digits of a station frequency, with the first bar flashing. Enter the first digit of the station frequency using the NUMERIC buttons. The digit appears in the frequency display and the second bar flashes. Enter the remaining digits of the frequency. When all of the digits have been entered, the tuner automatically tunes to the displayed station frequency. NOTE: On the USA version, pressing 1 in the FM mode will enter 10 as the digit in the frequency display. On the European version, it is necessary to press 1 and then 0 to enter 10. For US FM stations, press only one digit following the decimal point as shown in the first example below. For European FM stations, press two digits following the decimal point as shown in the second example. EXAMPLES: TUNING Buttons CH TUNING Buttons The buttons labeled TUNING on the front panel or CH UP/DOWN on the remote control provide two different tuning functions, depending on the mode of operation. In the normal FREQUENCY TUNING mode, press a TUNING button and release to manually jump up or down to the next station frequency, regardless of whether or not a station is broadcasting on that frequency. For auto scan tuning, press and hold the TUNING button for approximately one second. An AUTO indicator appears in the front panel display and the tuner begins automatically scanning up or down through the frequencies until the next available station is detected. If this is not the desired station, repeat the automatic tuning procedure to find the next station. [. . . ] To turn Zone 2 on or off, press the POWER on the remote. To adjust the volume button on in Zone 2, press the VOLUME buttons the remote. To select a different analog input source, press one of the INPUT SOURCE buton the remote. tons The Zone 2 outputs provide a VARIABLE level signal, with control of the volume from the RX-1050 front-panel and/or remote control from Zone 2. NOTE: Zone 2 cannot be controlled from the remote in the main room. NOTE: ZONE REM IN Jack See Figure 6. This 3. 5 mm mini-jack accepts signals from a infrared repeater located in Zone 2. [. . . ]