User manual ROYAL SOVEREIGN LAMINATOR

[. . . ] WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding lamination rollers which are warranted for Six (6) months. This warranty is extended only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign's sole and exclusive liability and the customer's sole and exclusive remedy under this warranty shall be, at Royal Sovereign's option, to repair or replace any such defective part or product. [. . . ] LOWER TEMPERATURE ­ Displays lower roller set temperature. SPEED ­ Displays set speed. F 7. PRGM ­ Displays set memory. 6 RSS, RSR, RSH Series Control Buttons 1. UPPER: To change upper roller temperature by pressing button, then up or down arrow. LOWER: To change lower roller temperature by pressing button, then up or down arrow. 1 2 3 4 5 Inches Lamination 1/25" 3/16 ~1/4" 3/8 ~1/2" 3/5" RSH Series Only 15 Metric (mm) Lamination 1 5-7 10-13 NOTE: If you don't want to laminate, please place the pressure lever to the "Open position(NO. 5). " 7 8 RSS, RSR, RSH Series 9. USING FOOT PEDAL AND REMOTE CONTROL USING FOOT PEDAL Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot pedal to operate the laminator for "Hands Free Operation. " To activate the machine, press the foot pedal once and then release. USING REMOTE CONTROL Located on the left hand side of the rear of the laminator, to use press: 1. Press and hold the button (useful for jams or misfed media). Once you activate the slitter then you can begin lamination. USING SLITTER Only the RSR & RSS series have slitters included 1. Adjust the left and/or right slitters by loosening the slitter adjuster knob (located between the front and rear rollers. ) (Figure 1) Figure 1 2. Activate the slitter by turning the slitter knob (located on the left side of the machine) clockwise. USING CROSS CUTTER The cross cutter is located on the rear exit table of the machine. After lamination, move the cutter approximately to the center of the completed application at the desired point of detachment (Figure 1). Figure 3 4. To deactivate the slitter turn the slitter knob counterclockwise. Grasp film with one hand, press the cutter downward into the application and slide it first to one end of the application, then to the other end to complete the cut (Figure 2 & 3). Figure 2 NOTE: When the slitter becomes dull break off the blade. Loosen the screw to pull down a new blade. Once the new blade is down tighten the screw. (Figure. 5 ) Figure 5 CAUTION When the slitters are not in use please keep the slitters positioned at the far left and right side to avoid injury. Figure 3 9 10 RSS, RSR, RSH Series 12. LOADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). [. . . ] Install the right rewinder on the outside of the frame and connect the motor wire connector to the rear wire (Figures 8 & 9). Figure 8 Installing the Rear Rewinder Option (Includes motorized winder, bracket, one spindle, and mounting hardware). Remove the left and right covers by using a Phillips screwdriver (four screws on each side cover) (Figures 2 & 3). Figure 2 Figure 3 6. Remove the lever knob screw and lever (Figure 4). Figure 9 Figure 4 3. Remove the rear cover by removing all 12 screws (4 top, 4 bottom, and 2 on each side) (Figure 5 & 6). Figure 5 Figure 6 17 18 Curled lamination: Symptom Removing Adhesive Build Up Unclear lamination: Machine will not turn on: The unit is not heating up: There is power, but the rollers are not turning after the "RUN" button is pressed: 1. [. . . ]