User manual RUSSOUND CAM66T 1

[. . . ] CAM6. 6T-S1 System 6-Zone, 6-Source AM/FM Receiver and UNO-S1 Smart Keypads INSTRUCTION MANUAL IMPORTANT SAFEGUARDS 9. Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. 10. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. [. . . ] The tip is positive (+) and sleeve is negative (-). The default setting for the Mute Trigger Out provides 12VDC whenever 12VDC is applied to the Mute Trigger In. CAM6. 6 Doorbell Interface 35 INSTALLER MAKING CONNECTIONS RNET Link In and Link Out The RNET Link In and Link Out can be used to connect two to six CAM6. 6 or CAV6. 6 controllers. The connection is made using a CAT-5 patch cable from the Link Out of the master CAM6. 6 and into the Link In of the next controller. Along with RNET data signals, the RNET Link In and Link Out jack passes the six source IR signals. These are only for source-specific IR remote repeating, not codes initiated from the controller's internal IR library. The CAT-5 patch cable should not exceed 18 inches in length to avoid potential cross-talk between the sourcespecific IR repeating signal lines. The RNET Link In and Link Out is also used to connect the CAM6. 6 to other Russound products with RNET. Note: If two or more CAM6. 6 or CAV6. 6 controllers will be connected using the RNET Link In and Link Out ports, each controller must have a unique Controller ID prior to being connected through the RNET ports. The Controller ID assignment must be performed during the Controller Setup section of the Installation menu. CAM6. 6 (Controller ID 1) CAT-5 Cable (MAX LENGTH 18 INCHES) CAM6. 6 CAV6. 6 (Controller ID 2) 36 INSTALLER MAKING CONNECTIONS RS-232 Interface The CAM6. 6 supports RS-232 communication with various third party automation systems or PC for programming of the controller. The RS232 com port is located on the back of the CAM6. 6 and uses a DB-9 cable connection. For RS-232 protocol and the backup PC application, see the Document Center at www. russound. com. Look for the Technical Documents under Multi-source/Multi-room products. CAM6. 6 INTERFACE DB9 Cable 37 INSTALLER MAKING CONNECTIONS Optional Internal Source - AM/FM Tuner Antennas AM Antenna Connect the included loop antenna for AM reception to the Optional Internal Source panel, attaching the GND (ground) and AM ends to the appropriately marked connections. FM Antenna Attach the included FM antenna for FM reception to the Optional Internal Source panel by pushing the F-type quick-connect termination of the antenna onto the FM connection. CAM6. 6 38 INSTALLER MAKING CONNECTIONS Optional Internal Source - AM/FM Tuner Antennas Connecting an Alternate Outdoor Antenna for AM/FM The diagram below depicts a suggested installation option of an alternate outdoor FM antenna and AM antenna. For best performance for AM reception, it is recommended to use an external outdoor or atticmounted long wire antenna for best performance for AM reception. Use a 75-ohm to 300-ohm balun at the AM connection on the tuner, and attach the 75-ohm coax cable to the balun. For best performance for FM reception, it is recommended to use an external outdoor or atticmounted antenna. Attach the desired length of 75-ohm coax cable directly to the FM connection on the tuner. 300 ohm to 75 ohm balun CAM6. 6 39 INSTALLER MAKING CONNECTIONS Grounding Outdoor Antennas Antenna Lead In Wire Electric Service Equipment Grounding Conductors Power Service Grounding Electrode System Ground Clamps Grounding an Outdoor Antenna If the tuner is used with an outdoor antenna, the antenna must be grounded against static charges and voltage surges. Consult the instructions that came with the antenna or contact the antenna manufacturer for proper installation instructions. The diagram above gives a general depiction of how an outdoor antenna should be grounded. For complete guidelines on antenna grounding procedures, please consult the National Electrical Code, Section 810, ANSI/NFPA No. 70-1984. 40 INSTALLER INITIAL INSTALL TEST Before proceeding to the system programming section, it's important to conduct an initial test to determine that the hardware components are working properly. Connect the speaker wires from Zone #3 to the CAM6. 6 Zone #3 speaker output connectors. Connect an UNO-S1 keypad to Keypad Port #3 on the rear of the CAM6. 6. Connect a source to the Source #3 Input on the CAM6. 6 using RCA Audio patch cables. [. . . ] Audio from the source tuner can be split if shared by all controllers. CAM6. 6T Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = All Controllers Output/Input Switch = Internal Source Output RCA cable connected to Source 1 CAM6. 6 (no tuner installed) Controller Setup Menu: Controller ID = 2 Source Setup Menu: Basic Setup Procedure: Source # = 1; Source Name = Tuner; Command Type = Peripheral Output/Input Switch = Input RCA cable connected to Source 1 102. 5 102. 5 102. 5 UNO-S1 CAM6. 6 Back Panel (Controller ID 1) CAM6. 6 RCA Cables 102. 5 102. 5 102. 5 UNO-S1 CAM6. 6 Back Panel (Controller ID 2) CAM6. 6 103 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH TWO TUNERS System with two CAM6. 6T (internal tuner) controllers The configuration below is suitable for 7 to 12 zones that will have access to the tuner in the controller to which its keypad is connected only. Built-in tuners are always Source 1 and cannot be changed. If you have more than one internal tuner, you must set each tuner to its specific Controller ID number. If you want each controller to have access to dual tuners, a suggested solution is to use an ST2 Dual Tuner with two CAM6. 6s (see next page). CAM6. 6T (1) Controller Setup Menu: Controller ID = 1 Peripheral Setup Menu: Controller ID = 1 CAM6. 6T (2) Controller Setup Menu: Controller ID = 2 Peripheral Setup Menu: Controller ID = 2 A CAT-5 patch cable is use to connect the RNET Link Out of Controller 1 to the RNET Link In of Controller 2. 102. 5 102. 5 102. 5 UNO-S1 CAM6. 6 CAM6. 6 Back Panel (Controller ID 1) 92. 5 92. 5 92. 5 UNO-S1 CAM6. 6 CAM6. 6 Back Panel (Controller ID 2) 104 SAMPLE CONFIGURATIONS MULTIPLE CONTROLLERS WITH THREE TUNERS Sharing an ST2 Dual Tuner with multiple CAM6. 6 controllers (with and without tuners) The configuration below is suitable for 7 to 12 zones that can access the ST2 Dual Tuner and the CAM6. 6T tuner. [. . . ]