User manual RUSSOUND RAVE1

[. . . ] Crimp an RJ-45 connector on the system end of the CAT-5 cable, following the T568A standard as shown. With the system turned off, plug the connector into the RNET A/V jack on the system controller or RAVD1 Decoder. (If using a wall plate, punch down the CAT-5 per the T568A standard and use a straight-through patch cable between the system and the wall plate. ) Note: Do not plug the CAT-5 cable into an RNET Link jack. It must be plugged into an RNET A/V jack on either the system controller or the RAVD1 Decoder. [. . . ] This warranty does not cover: damage caused by abuse, accident, misuse, negligence, or improper installation or operation; power surges and lightning strikes; normal wear and maintenance; products that have been altered or modified; any product whose identifying number, decal, serial number, etc. Russound sells products only through authorized dealers and distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product. Damage to or destruction of components due to application of excessive power voids the warranty on those parts. In these cases, repairs will be made on the basis or the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit. Before returning a unit for repair, call Russound at 603. 659. 5170 for a return authorization number. Write this number on the shipping label and ship to: Russound, 5 Forbes Road, Newmarket, NH 03857. Overview The RAVE1 RNET A/V Encoder enables the use of a remote source with a Russound RNET® or other multiroom audio-video system. It connects to the source equipment and sends audio and video signals to the multiroom system over a single CAT-5 cable. It also provides either RNET or infrared control of the source equipment. Housed in a compact surface-mount metal box, the RAVE1 provides connectors for RNET Link, IR emitter, stereo audio, and composite video. A special RJ-45 jack connects through the CAT-5 cable to either an RAVD1 RNET A/V Decoder or an RNET A/V-enabled multiroom controller at the system end. The RAVE1 comes with a 12 VDC power supply and patch cables for connecting to the source equipment. Setup for RNET Control Note: For RNET control of the remote source, both the source equipment and the system controller must be RNET capable. If the RNET controller does not have an RNET A/V jack, you will need to use an RAVD1 Decoder at the controller to receive signals from the Encoder. Using the supplied RJ-45 patch cable, connect from an RNET Link jack on the source equipment to the RNET Link jack on the Encoder. Use the supplied RCA patch cable to connect from the source equipment's audio and video outputs to the Encoder's inputs. Crimp an RJ-45 connector on the system end of the CAT-5 cable, following the T568A standard as shown. With the RNET system turned off, plug the connector into the RNET A/V source input jack on the RNET system controller or RAVD1 Decoder. (If using a wall plate, punch down the CAT-5 per the T568A standard and use a straight-through patch cable between the system and the wall plate. ) Note: Do not plug the CAT-5 cable into an RNET Link jack. It must be plugged into an RNET A/V jack on either the system controller or the RAVD1 Decoder. [. . . ] Do not use this apparatus near water. RCA Patch Cable RCA Patch Cable RJ-45 Patch Cable 1 CAT-5 Cable (up to 300 feet) RJ-45 Patch Cable RNET A/V Encoder RJ-45 Wall Plates (optional) Connections for RNET control of source CAV6. 6 Multiroom Controller 2 1 3 4 5 11. Use only attachments or accessories specified by the manufacturer. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart-apparatus combination to avoid injury from tip-over. [. . . ]