User manual RUSSOUND ST2

[. . . ] ST2 Smart Tuner Dual AM/FM Tuner Installation Manual IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] After a tuner is selected, the next button press refreshes the display with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. TUNER 1 TUNER 2 Selecting Distant or Local Reception Press to toggle between Distant and Local mode. DISTANT or LOCAL appears briefly on the screen when selecting mode. Normal operation is in Distant mode. LOC/ DX Recalling a Memory Preset To recall a memory preset, select the desired tuner, press MEM BANK to select the desired bank, then press Selecting the desired band Push AM/FM and enter the desired preset number (1 to 6). The memory presets can also be accessed by using MEM to switch between AM and FM reception. Selecting the desired frequency TUNE and to scroll through all presets for the selected bank. MEM Use and for manual tuning. To move quickly through the stations, press and hold either of the Tune buttons for more than 1. 5 seconds. TUNE Saving Favorites The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding FAV 2 FAV 1 To directly select a station, press , and enter the three- or four-digit station frequency (1071 for 107. 1, etc. ). European regions use five-digit station frequencies. TUNE or until "FAV1 (2) saved" appears on the tuner. Stored Favorites are then recalled by pressing either FAV 1 Frequency Seek The SEEK function is performed by pressing and releasing to seek lower frequencies or for higher frequencies. SEEK tuning begins at the current frequency, seeks upward and stops at the next tuned station. Once the highest frequency is reached, the tuner continues in SEEK mode at the lowest frequency. or FAV 2 . 15 ST2 OPERATION ST2-KP KEYPAD CONTROL ST2-KP Keypad Operation 1 5 ST2-KP Keypad Display Turning the keypad on/off To activate the ST2-KP, press . The keypad remains powered until the ST2 Tuner is turned off. 1 The 5-character backlit display shows frequency and band, plus presets. Messages scroll twice, then display the first 5 characters. Selecting the desired tuner To select a different tuner, press and hold . (If the keypad has been hardware jumper-selected to Tuner 1 or Tuner 2, it will not switch between the two tuners. ) The backlight color of the display will be green for Tuner 1 and amber for Tuner 2. Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. 2 ST2-KP Keypad-Front Panel 5 Selecting the desired band to switch between AM or FM band. 3 2 3 4 1 Push 3 Selecting the desired frequency and for manual tuning. To move quickly or Use through the channels, press and hold either for more than 1. 5 seconds. European frequencies show in . 05 MHz increments. 4 Selecting a Bank To select a bank, select the desired tuner, then press and hold or to select the desired bank. The bank name will show on the display. 4 Recalling a Memory Preset or To recall a memory preset, press and release to scroll through the presets for the selected bank. (Memory presets must be stored for ST2-KP recall) 16 ST2 OPERATION UNO-S2 KEYPAD CONTROL WITH RNET CONTROLLER UNO-S2 Keypad Operation NOTE: To control the ST2 Tuner through the UNO-S2 keypad, the tuner must be configured as a source using the RNET Controller programming steps. Turning the unit on The tuner is power managed by the RNETenabled controller. If the tuner is in standby mode, any button press of the UNO-S2 keypad will bring the tuner out of standby mode. Selecting the desired tuner On the UNO-S2 keypad, press to select Frequency Scan To scan, press and hold then release . The tuner scans through tuned stations with a 5-second preview before moving to the next station. To end scanning, press Selecting a Bank To select a bank, press and hold up or for bank again. for bank down. [. . . ] Repeat steps 4 through 7 to configure the second tuner. Press the Setup button three times to back out of the Installation Menu. Source Configuration Note: When the ST2 Tuner is used with the CAV6. 6 or other RNET controller, it is configured as an RNET command type PERIPHERAL and is connected via the RNET bus. This makes the tuner behave as a fully integrated device with UNO keypad support. Each tuner must be set up with a unique source number (1 - 6) or unassigned. [. . . ]