User manual RUSSOUND ST2-XM2

[. . . ] 2 800. 967. 2346 IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] The ST2-XM2 front panel displays information for the tuner that is receiving commands from the ST2RC. However, the ST2-RC commands do not change which tuner is playing; that is done through the system's source selection. number (1 to 6). The memory presets can also be MEM accessed by using and presets for the selected bank. MEM to scroll through all Saving Favorites The remote control stores two "favorites" (similar to memory presets) per tuner. These are set simply by selecting either Tuner 1 or Tuner 2, setting the desired frequency and pressing and holding FAV 2 FAV 1 Turning the unit on/off To switch the ST2 tuner in or out of standby mode, push TUNER 2. PWR or or any other button except TUNER 1 or until "FAV1 (2) saved" appears on the tuner. Stored Favorites are then recalled by pressing either FAV 1 or FAV 2 . Selecting the desired tuner To control a tuner, push or . When pressed, these buttons will be backlit green for Tuner 1 (XM1) and amber for Tuner 2 (XM2). Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. TUNER 1 TUNER 2 Selecting the desired channel TUNE Use and for manual tuning. To move quickly through the channels, press and hold either of the Tune buttons for more than 1. 5 seconds. TUNE To directly select a channel, press , and enter the two- or three-digit XM channel number. TUNE Selecting an XM mode Push OK to select an XM operating mode. Exiting an XM mode Push menu. ST/ MONO to exit the XM operating mode selection Recalling a Memory Preset To recall a memory preset, select the desired tuner, press BANK and enter the desired bank number MEM (1-6), then press and enter the desired preset 19 ST2-XM2 OPERATION ST2-KP KEYPAD CONTROLS ST2-KP Keypad Operation 1 Turning the keypad on/off 4 Recalling a Memory Preset or To activate the ST2-KP, press . The keypad remains powered until the ST2-XM2 Tuner is turned off. 1 To recall a memory preset, press and release to scroll through the presets for the selected bank. (Memory presets must be stored for ST2-KP recall) 5 Selecting the desired tuner To select a different tuner, press and hold . (If the keypad has been hardware jumper-selected to Tuner 1 or Tuner 2, it will not switch between the two tuners. ) The backlight color of the display will be green for Tuner 1 (XM1) and amber for Tuner 2 (XM2). Each time a tuner is selected the display will refresh with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. 2 ST2-KP Keypad Display The 5-character backlit display shows XM channel and mode information. Messages scroll twice, then display the first 5 characters. ST2-KP Keypad-Front Panel Selecting an XM mode to select an XM operating mode. Push 2 Exiting an XM mode 5 Press and release until EXIT is displayed to exit the XM operating mode menu. 3 Selecting the desired channel and for manual tuning. To move quickly or 4 3 2 Use 3 1 through the channels, press and hold either for more than 1. 5 seconds. 4 Selecting a Bank To select a bank, select the desired tuner, then press and hold or to select the desired bank. The bank name will show on the display. 20 ST2-XM2 OPERATION UNO-S2 KEYPAD CONTROLS WITH CAV6. 6/CAM6. 6 CAV6. 6-UNO-S2 Keypad Operation NOTE: To control the ST2 Tuner through the UNO-S2 keypad, the tuner must be configured as a source using the CAV6. 6/CAM6. 6 programming steps. Turning the unit on The tuner is power managed by the CAV6. 6 or other RNET-enabled controller. If the tuner is in standby mode, any button press of the UNO-S2 keypad will bring the tuner out of standby mode. Selecting the desired tuner On the UNO-S2 keypad, press to select strength rating. To exit, press Selecting a Bank To select a bank, press and hold up or again. for bank for bank down. The bank's name will be temporarily displayed on the UNO-S2. Recalling a Memory Preset Press and to scroll through the memo- ry presets for the selected bank. This procedure will step through all of the presets in the current bank, then loop back to start at the first one. Only configured presets will be displayed. [. . . ] Each tuner must be set up with a unique source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus. Key Function Note: When using the tuner with the CAM6. 6-S2 system, do not reassign keypad and remote buttons for tuner control in the CAM6. 6 Key Configuration Menu. When the tuner is assigned the "Peripheral" command type in the CAM6. 6 Setup Menu, key assignments and functions are automatically assigned and will operate as shown in the preceding UNO-S2 keypad and UNO-LRC1 remote diagrams. 33 TECHNICAL SPECIFICATIONS ST2-XM2 Smart Tuner Dimensions: Weight: Power Supply: XM Band: XM Antenna: 17"W x 8"D x 1. 8"H (43 x 20. 3 x 4. 4 cm) 7 lbs. [. . . ]