User manual RUSSOUND ST2S

[. . . ] ST2S Smart Tuner Installation Manual IMPORTANT SAFEGUARDS 11. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. 13. Cleaning - The appliance should be cleaned only as recommended by the manufacturer. [. . . ] to select an SIRIUS operating mode. Selecting a mode (SIRIUS) Push Mode Band . Exiting a mode (SIRIUS) Push to exit the SIRIUS mode selection menu. Signal Strength mode (SIRIUS) Press and hold and release. Push the desired memory preset (M1 through M6) button for more than 2 seconds. When the memory preset is saved, the appropriate preset number (M1 through M6) and SAVED appears on the LCD. The selected station setting reappears and the sound resumes after the button is released. Recalling a Memory Preset To recall a memory preset, use to select the desired bank, then press the desired preset button (M1 to M6). In addition to direct selection, the memory presets can be accessed by using and to scroll through all presets for the bank selected. the signal strength rating. To exit press Selecting the desired frequency or channel Press and release and for manual tuning. Selecting Stereo or Mono Output (AM/FM only) Press and release to toggle between stereo and mono mode. STEREO or MONO appears briefly on the screen when selecting mode. Backup and Restore Once all of the tuner settings are completed, it may be advisable to create a backup of the programmed settings for future use. The backup will then be available in case tuner settings need to be restored. The "RNET Backup Utility" is available through the Document Center at www. russound. com. Also required are a DB9 male-to-female cable and laptop or desktop PC. 21 Selecting Distant or Local Reception (AM/FM only) Press and hold to toggle between distant and ST2S OPERATION ST2-RC REMOTE CONTROL ST2-RC Remote Control Operation The ST2-RC remote control is the only means of remote operation of the ST2S in a non--RNET system. The ST2S front panel displays information for the tuner that is receiving commands from the ST2-RC. However, the ST2-RC commands do not change which tuner is playing; that is done through the system's source selection. Frequency Seek (AM/FM only) The SEEK function is performed by pressing and releasing to seek lower frequencies or for higher frequencies. SEEK tuning begins at the current frequency, seeks upward and stops at the next tuned station. Once the highest frequency is reached, the tuner continues in SEEK mode at the lowest frequency. Turning the unit on/off To switch the ST2 tuner in or out of standby mode, push TUNER 2. PWR Selecting Stereo or Mono Output (AM/FM only) Press to toggle between stereo and mono mode. STEREO or MONO appears briefly on the screen when selecting mode. On a preset, the stereo/mono setting is saved for that preset. ST/ MONO or any other button except TUNER 1 or Selecting the desired tuner To control a tuner, push or . When pressed, these buttons will be backlit green for Tuner 1 (SIRIUS) and amber for Tuner 2 (AM/FM). Each time a tuner is selected, the next button press will refresh the display with the current station or preset for that tuner, and all subsequent button presses and memory preset entries will be associated with that selected tuner. TUNER 1 TUNER 2 Selecting Distant or Local Reception (AM/FM only) Press to toggle between Distant and Local mode. DISTANT or LOCAL appears briefly on the screen when selecting mode. Normal operation is in Distant mode. LOC/ DX Selecting the desired band (AM/FM only) Push AM/FM to switch between AM and FM reception. Recalling a Memory Preset To recall a memory preset, select the desired tuner, press BANK Selecting the desired frequency or channel TUNE and enter the desired bank number MEM Use and for manual tuning. To move quickly through the stations or channels, press and hold either of the Tune buttons for more than 1. 5 seconds. TUNE (1-6), then press and enter the desired preset number (1 to 6). [. . . ] This makes the tuner behave as a fully integrated device with UNO-S2 keypad support. Each tuner must be set up with a unique source number (1 - 6) or unassigned. An unassigned tuner is not controlled by the RNET bus. Each of the ST2S modules can be configured as source number "unassigned" if the module is used in another system (e. g. , home theater) or will not be used as a source in the RNET system. [. . . ]