User manual RUSSOUND VBC KIT

[. . . ] Heat - The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat. Power Sources - The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. 9. Grounding or Polarization - Precaution should be taken so that the grounding or polarization means of an appliance is not defeated. 10. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, receptacles, and the point where they exit from the appliance. [. . . ] If water or any other liquid enters the cabinet, take the unit to a qualified service person for inspection. LIMITED WARRANTY The Russound CRX and CTX baluns are fully guaranteed for two (2) years from the date of purchase against all defects in materials and workmanship. For this warranty to apply, the unit must be installed and used according to its written instructions. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor. Accidental damage and shipping damage are not considered defects under the terms of this warranty. Russound assumes no responsibility for defects resulting from abuse or servicing performed by an agency or person not specifically authorized in writing by Russound. If service is necessary, it must be performed by Russound. Damage to or destruction of components due to excessive power voids the warranty. In these cases, the repair will be made at the owner's expense. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of the service required. Be sure to pack in a corrugated container with at least 3 inches of resilient material to protect the unit from damage in transit. Before returning a unit for repair, call Russound at (603) 659-5170 for a Return Authorization number. Write the RA number on the shipping label and ship to: Russound, ATTN: Service, 5 Forbes Road, Newmarket NH 03857 Russound sells product only through authorized Dealers and Distributors to ensure that customers obtain proper support and service. Any Russound product purchased from an unauthorized dealer or other source, including retailers, mail order sellers and online sellers will not be honored or serviced under existing Russound warranty policy. Any sale of products by an unauthorized source or other manner not authorized by Russound shall void the warranty on the applicable product. VBC Kit Composite A/V Balun Installation Manual INTRODUCTION The VBC Composite Audio Video Balun Kit contains a pair of active circuitry (powered) baluns for sending composite video and two-channel analog audio over a single CAT-5 cable. This kit includes a transmitter and receiver and would be used in multiroom audio-video distribution systems to remotely locate an audio-video source from a distribution or display device. The benefits of using this kit are that it uses low-cost CAT-5 cable, plus it eliminates ground loops, which may occur when remotely locating sources from displays. Ground loops are seen as lateral "hum" bars scrolling on the display and an audible hum in the audio. The kit also uses an active buffer switch that allows a source signal to be split and shared with another system. KIT CONTENTS 5 Forbes Rd. Newmarket, NH 03857 Tel 603. 659. 5170 · Fax 603. 659. 5388 e-mail: tech@russound. com 28-1246 01/24/06 (1) CTX transmitter module (1) CRX receiver module (1) 846C 12VDC 200mA power supply INSTALLATION You will need two sets of RCA cables and the appropriate length of CAT-5 cable. Also recommended are RJ45 modular wall plates mounted near the source and near the remotely located equipment. [. . . ] Otherwise, the switch should be left OFF (button raised). For the CAT-5 connection, use a CAT-5 patch cable with RJ45 connections at each end using the T568A wire configuration. Run the patch cable from the CTX to the wall plate. Run CAT-5 cable from the back of the wall plate to the back of the wall plate located near the remote display. At the RECEIVE end: The CRX is located at the remote end (TV, VCR, stereo, etc. ) of the system. [. . . ]