User manual RYOBI 400W TRIMMER / ROUTER EVT400K

[. . . ] OWNER'S OPERATING MANUAL TRIMMING AND ROUTING KIT MODEL EVT400K 1N. 1 /2 1 SPECIFICATIONS : Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400 watt No Load Speed . . . . . . . . . . . . . . . 30, 000 min-1 Max. Cutter Diameter . . . . . . 6. 35 mm Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 75 kg DOUBLE INSULATED N197 THANK YOU FOR BUYING A RYOBI TRIMMING AND ROUTING KIT Your new trimming and routing kit has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation and operator safety. Properly cared for, it will give you years of rugged, trouble free performance. [. . . ] Disconnecting your trimmer will prevent accidental starting that could cause serious injury. WARNING: If collet nut is not tightened securely, cutter may come out during use, causing serious personal injury. WARNING: Do not use cutters with undersized shanks. Undersized shanks will not tighten properly and could be thrown from tool causing injury. WARNING: Avoid open area of trimmer base. Serious personal injury will result from contact with a rotating cutter. WARNING: Do not use cutters that are larger in diameter than the opening in trimmer base. Use of such cutters will come in contact with the trimmer base and damage both the cutter and trimmer base. Possible loss of control or create other hazardous conditions that could cause possible serious personal injury. Wrench On Collet Nut Cutter Wrench On Spindle Flats INSTALLING/REMOVING CUTTERS (Fig. 1) UNPLUG YOUR TRIMMER. WARNING: Failure to unplug your trimmer could result in accidental starting causing serious injury. TO SET THE DEPTH OF CUT (Fig. 1 Place your trimmer upside down on a workbench in order to gain easy access to the spindle and collet nut. Place the small end of one of the wrenches provided on the spindle flats. Place the large end of the other wrench provided onto the collet nut. Rotate wrench counterclockwise to loosen collet nut. WARNING: Failure to unplug your trimmer could result in accidental starting causing serious injury. WARNING: If you are changing a cutter immediately after use, be careful not to touch the cutter or collet with your hands or fingers. They may get burnt due to the heat buildup from cutting. Always use the wrench provide. Loosen the wing bolt and move the base until the tip of cutter touches the work surface. Position your trimmer so that the cutter can extend below the sub base for desired depth of cut setting. Move the base to obtain the desired depth of cut. The distance the cutter moves will be indicated on the depth of cut scale. Each mark on the scale indicates a 1. 6 mm change in depth setting. Indicator points are located on the base. Securely tighten the wing bolt. Page 4 CHANGING THE ROTATION SPEED (FIG. 7) OPERATION Depth of Cut Scale 1N. 1 /2 1 CIRCUMFERENCE CUTTING (Fig. 4 - 6) By installing the straight fence and connector you can make a circumference cut. Available radius cuts, shown from bit to central hole. Minimum radius: 70mm Maximum radius: 220mm Attention: The straight fence is unable to cut a radius between 172mm and 186mm. Wing Bolt Fig. [. . . ] Then return the collet nut to its original position. WARNING: Do not at anytime let brake fluids, fuel, petroleum-based products, penetrating oils, etc. They contain chemicals that can damage, weaken or destroy plastic. Use clean cloths to remove dirt, carbon dust, etc. When electric tools are used on fibreglass boats, sports cars, wallboard, spackling compounds or plaster, it has been found that they are subject to accelerated wear and possible premature failure, as the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently it is not recommended that this tool be used for extended work on any fiberglass material, wallboard, spackling compounds or plaster. [. . . ]