User manual RYOBI AP10

[. . . ] Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your tool properly and only for what it is intended, you will enjoy years of safe, reliable service. Please fill out and return the Warranty Registration Card so we can be of future service to you. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS I Table of Contents, Introduction, and Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 I Rules For Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] I Place planer on workbench aligning holes in the planer base with holes drilled in the workbench. I Insert four bolts (not included) and tighten securely with lock washers and hex nuts (not included). Note: All bolts should be inserted from the top. Install the lock washers and hex nuts from the underside of the workbench. Supporting surface where planer is mounted should be examined carefully after mounting to insure that no movement during use can result. If any tipping or walking is noted, secure workbench or support surface before beginning planing operation. I Mark holes on board where planer is to be mounted using holes in planer base as a template for hole pattern. I Follow last three steps in section Mounting Planer to Workbench. If lag bolts are used, make sure they are long enough to go through holes in planer base and material the planer is being mounted to. If machine bolts are used, make sure bolts are long enough to go through holes in planer base, the material being mounted to, and the lock washers and hex nuts. CLAMPING PLANER TO WORKBENCH See Figure 5. If the planer is to be used as a portable tool, it is recommended you fasten it permanently to a mounting board that can easily be clamped to a workbench or other stable surface. The mounting board should be of sufficient size to avoid tipping while planer is in use. 7 ADJUSTMENTS THICKNESS SCALE ADJUSTMENT See Figure 8. Located on the right front of the planer, the thickness scale shows the depth of the finished workpiece. Inaccurate cuts can be prevented by routinely checking the alignment of the thickness scale. I Table extensions must be level with planer table. I Plane a scrap piece of wood and measure the depth of the finished piece. I If properly adjusted, the depth of the finished piece should be the same as indicated on the thickness scale. I If out of adjustment, loosen the two screws holding the scale indicator and adjust the thickness indicator to the correct setting. I Retighten screws securely. THICKNESS SCALE SCALE INDICATOR SCREWS SCALE INDICATOR REPLANE INDICATOR ADJUSTMENT See Figure 9. Plane a scrap piece of wood and measure the depth of the finished piece. If an adjustment is needed: I Unplug your planer. Fig. 8 DEPTH ADJUSTMENT HANDLE PHILLIPS SCREW WARNING: Failure to turn the planer off, remove the switch key, and unplug the planer could result in accidental starting causing possible serious personal injury. [. . . ] Replace, turn or sharpen cutter blades 3. Check for adequate power supply, check cord and plug for damage, check condition of motor brushes 1. Have service performed by Ryobi Authorized Service Center 3. Have service performed by Ryobi Authorized Service Center 1. [. . . ]