User manual RYOBI BD24SR SCHEMA

[. . . ] 3-6 Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking and Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-13 Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is now ready to transport. SAW ARM 10 in. (254 mm) saw blade is included with your miter saw. It is fine for most wood cutting operations, but for fine joinery cuts or cutting plastic, use one of the accessory blades available from your nearest dealer. CARRYING HANDLE UPPER BLADE GUARD LOCK PIN SWITCH TRIGGER BLADE 15 15 30 45 LOWER BLADE GUARD DUST BAG FENCE MITER TABLE 45 NO HANDS ZONE LABEL BLADE WRENCH WRENCH STORAGE AREA MITER TABLE BASE 15 45 31. 62 22 . 5 MITER SCALE MITER LOCK PLATE 30 22. 5 30 31. 62 CONTROL ARM POSITIVE STOP (S) "NO HANDS ZONE" BOUNDARY LINE Page 8 MITER LOCK HANDLE Fig. 2 FEATURES MITER LOCK HANDLE See Figure 3. The miter lock handle securely locks your saw at desired miter angles. CARRYING HANDLE LOCK PIN SPINDLE LOCK BUTTON See Figure 4. A spindle lock button has been provided for locking the spindle of your saw in a stationary position. Only depress and hold the spindle lock button while installing, changing, or removing blade. SAW ARM TRIGGER LOCK See Figure 5. To prevent unauthorized use of your miter saw, we suggest that you disconnect it from the power supply and lock the switch in the off position. To lock the switch, install a padlock through the hole in the switch trigger. A lock with a long shackle up to 19/64 in. When the lock is installed and locked, the switch is inoperable. (90 cm) wide, providing support for cutting long workpieces. The stop block provides a stop for making repetitive cuts to same length. It can be installed on either side of saw base. The work clamp provides a means for clamping workpiece securely against the fence when making a cut. Standard "C" clamps can also be used for this purpose. The dust bag catches sawdust, helping keep work area cleaner. WARNING: Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. TRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERN 31 . 6 TRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERN 45 45 30 22. 5 30 31 . 6 15 0 15 22. 5 SAW BASE MOUNTING SURFACE Fig. 6 Page 10 ASSEMBLY WARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts, make sure all adjustments are complete, and make sure all fasteners are secure before connecting saw to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. 15 MITER TABLE 30 31. 62 45 TO TIGHTEN As mentioned previously your saw has been factory assembled and adjusted. The miter lock handle, dust guide or dust bag, table extensions, stop block, and blade are the only parts that have to be installed. 45 31. 62 30 22. 5 MITER LOCK HANDLE See Figure 7. To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threaded hole in the control arm under miter table. [. . . ] Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury. WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. LUBRICATION All of the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the unit under normal operating conditions. Therefore, no further lubrication is required. Page 19 TROUBLESHOOTING PROBLEM Saw will not start. CAUSE 1. Have switch replaced by an Authorized Service Center. [. . . ]