User manual RYOBI BT3000SXI

[. . . ] 2 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Glossary of Terms For Woodworking . . . . . . . . . . . . . . . . . . . . . . 8 Unpacking and Tools Needed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] I Bring the blade back to the desired angle and height. Insert the throat plate, lower the blade, and secure the throat plate with the throat plate screw. 29 RIVING KNIFE MOUNTING PLATE SHIMS HEX NUTS Page 25 Fig. 30 OPERATION TO ADJUST THE BLADE DEPTH The blade depth should be set so that the outer points of the blade are higher than the workpiece by approximately 1/8 in. but the lowest points (gullets) are below the top surface. GULLET WARNING: Unplug the saw and make sure the blade guard assembly is installed and working properly to avoid serious personal injury. I Push the bevel locking lever to the left for elevation mode. I Raise the blade by turning the blade adjusting handle clockwise or lower it by turning the handle counterclockwise. Fig. 31 ANGLED BLADE BEVEL LOCKING LEVER TO ADJUST THE BLADE ANGLE See Figure 32. WARNING: Unplug the saw and make sure the blade guard assembly is installed and working properly to avoid serious personal injury. I Push the bevel locking lever to the right for angle mode. I Angle the blade by turning the blade adjusting handle until the bevel indicator shows the correct angle. 35 WARNING: Never use rip fence as cutoff gauge when crosscutting. SWITCH COVER TO STOP (A) WARNING: Make sure the blade guard assembly is installed and working properly to avoid serious personal injury. It is recommended you make test cuts on scrap wood. I Remove the rip fence by lifting the locking handle. I Set the blade to the correct depth for the workpiece. I Set the miter fence to 90° with the quick-stop or the miter scale. I Make sure the miter fence won't touch the blade while feeding the wood. The miter fence should not contact the blade. Loosen the adjusting clamp to move the fence if needed. I Place a support (the same height as saw table) behind the saw for the cut work. SWITCH BUTTON TO START TO STOP (B) TO LOCK IN OFF POSITION PADLOCK (NOT PROVIDED) Fig. [. . . ] Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. PARTS LIST FOR FIGURE 64 KEY NO. 1 2 3 4 5 6 DESCRIPTION QUAN. Leveling Foot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hex Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]