User manual RYOBI CFP180SM SCHEMA

[. . . ] Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your Power Planer properly and only for what it is intended, you will enjoy years of safe, reliable service. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS I I I I I I I I I Table of Contents / Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Some examples of these chemicals are: · lead from lead-based paints, · crystalline silica from bricks and cement and other masonry products, and · arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. I I SYMBOLS Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL V A Hz W min NAME Volts Amperes Hertz Watt Minutes Alternating Current n0 No Load Speed Class II Construction . . . /min Revolutions or Reciprocation Per Minute Safety Alert Symbol DESIGNATION / EXPLANATION Voltage Current Frequency (cycles per second) Power Time Type or a characteristic of current Rotational speed, at no load Designates Double Insulated Construction tools Revolutions, strokes, surface speed, orbits etc. per minute Indicates danger, warning or caution. Do not expose to rain or use in damp locations. Wet Conditions Alert 5 SYMBOLS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures. SYMBOL MEANING DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always place the cord to prevent it from hanging on the work while cutting. Fig. 5 DANGER: If the cord hangs up on the work during a cut, release the trigger switch immediately. Unplug your planer and check cord for damage. If no damage, reposition the cord to prevent it from hanging up again. If the cord has been damaged, have it replaced before using your planer. WRONG WARNING: Using your planer with a damaged cord could cause electrical shock resulting in serious injury. 6 Know the right way to use your planer. Never use your planer as shown in Figures 6 and 7. To help keep control, always support your work so the cut will be on your right. Clamp your work so it will not move during the cut. The work moving during a cut could result in the loss of control of your planer possibly causing serious injury. WRONG Fig. 7 10 OPERATION TO ADJUST PLANING DEPTH See Figure 8. [. . . ] PUSH BLADE INTO BLADE HOLDER BLADE BLADE HOLDER I Fig. 20 BLADE Use a screwdriver to push the blade into the blade holder until it is centered into position. 18 PULL BLADE FROM BLADE HOLDER Fig. 21 I I Using the blade wrench, retighten the three blade securing screws. [. . . ]