User manual RYOBI CMI1802 SCHEMA

[. . . ] 3-4 n Specific Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 n Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 n Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 n Glossary of Terms. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] n Holding both wrenches firmly, push the smaller wrench to the back of the machine. Make sure the hex nut is securely tightened. NOTE: Arbor shaft has right-hand threads. Check all clearances for free blade rotation. n Lower the blade by turning the height adjusting handwheel clockwise. HEX NUT TO LOOSEN INNER BLADE WASHER Fig. 9 SMALL WRENCH TO TIGHTEN ARBOR HEX NUT LARGE WRENCH SMALL WRENCH Fig. 8 LARGE WRENCH 16 ASSEMBLY WARNING: It is important to install and adjust the blade guard assembly correctly. Poor alignment could cause kickback and throw the workpiece at the operator. If the spreader and saw blade are not in alignment, adjustment is needed. To adjust: n Unplug the saw then raise the blade guard assembly. n n n n Not following correct operating procedures Misusing the saw Failing to use the anti-kickback pawls Cutting with a dull, gummed-up, or improperly set blade AVOIDING KICKBACK WARNING: Always wear safety goggles or safety glasses with side shields when operating power tools. Failure to do so could result in objects being thrown into your eyes resulting in possible serious injury. n Always use the correct blade depth setting. The top of the blade teeth should clear the workpiece by 1/8 in. n Inspect the work for knots or nails before beginning a cut. Knock out any loose knots with a hammer. n Always use the rip fence when rip cutting and the miter gauge when cross cutting. This helps prevent twisting the wood in the cut. n Always use clean, sharp, and properly-set blades. n To avoid pinching the blade, support the work properly before beginning a cut. n When making a cut, use steady, even pressure. [. . . ] If operation is dusty, also wear a dust mask. GENERAL MAINTENANCE Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc. WARNING: Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc. , come in contact with plastic parts. Chemicals can damage, weaken, or destroy plastic which may result in serious personal injury. [. . . ]