User manual RYOBI HP472

[. . . ] OPERATOR'S MANUAL 7. 2 VOLT CORDLESS DRILL-DRIVER HP472 Your cordless drill-driver has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. PACKING LIST Cordless Drill Battery Pack Charger Double-ended Bit 26-Piece Bit Set Operator's Manual Warranty Registration Card WARNING: To prevent accidental starting that could cause serious personal injury, always remove the battery pack from the tool when assembling parts. 10 OPERATION WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. Align raised rib on battery pack with groove in charging stand. n Press down on battery pack to be sure contacts on battery pack engage properly with contacts in charging stand. n The charge indicator light (LED), located on the charging stand, will light up red and glow when the charger is properly connected to power supply. This light indicates the charger is operating properly. It will remain on until battery pack is removed from charging stand or charger is disconnected from power supply. n After normal usage, 3 hours or less of charging time is required to fully recharge battery pack. n If both red and orange LED indicators glow, the battery pack is deeply or completely discharged, and 6 hours or longer of charging time is required to fully recharge battery pack. NOTE: If charger does not charge battery pack or orange LED continues to glow after more than 30 minutes of charging, return battery pack and charging assembly to your nearest Ryobi Authorized Service Center for electrical check. n The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. n Do not place charger in an area of extreme heat or cold. It will work best at normal room temperature. n When batteries become fully charged, unplug charger from power supply and remove the battery pack. WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury. WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury. APPLICATIONS You may use this tool for the following purposes: n Drilling in wood n Drilling in ceramics, plastics, fiberglass, and laminates n Drilling in both hard and soft metals n Using driving accessories, such as driving screws with screwdriver bits n Mixing paints CAUTION: To prevent damage to the battery pack, remove the battery pack from the charger immediately if no LED comes on. Return the battery pack and charger to your nearest service center for checking or replacing. Also, if you are removing the battery pack from the charger and no LEDs are on, return both the battery pack and the charger to your nearest service center. Do not insert another battery pack into the charger. A damaged charger may damage a battery pack. BATTERY SHOWN IN CHARGER CHARGING THE BATTERY PACK The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge overnight prior to use. [. . . ] Tap the hex key sharply with a mallet in a clockwise direction. This will tighten the chuck on the spindle. n Open the chuck jaws and remove the hex key. NOTE: The chuck screw has left hand threads. BATTERIES The battery pack for this tool is equipped with nickel-cadmium rechargeable batteries. [. . . ]