User manual RYOBI RT100

[. . . ] OPERATOR'S MANUAL Model RT100 Router Table Double Insulated (For use only with the Ryobi R161 router) THANK YOU FOR BUYING A RYOBI ROUTER TABLE Your new router table has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator's manual before using your new router table. Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. [. . . ] Remember that a careless fraction of a second is sufficient to inflict severe injury. FENCE ASSEMBLY Provides an adjustable surface to support and guide work. The fence may be adjusted to compensate for the stock reduced in the cut. FENCE ASSEMBLY GUARD/DUST COVER MITER GAUGE TABLE SURFACE LOWER GUARDS TABLE LEGS SWITCH BOX ASSEMBLY THROAT PLATES Fig. 1 Page 6 UNPACKING Before assembling your router table check to see that all parts listed are included. Inspect it carefully to make sure no breakage or damage has occurred during shipping. If any parts are damaged or missing, call 1-800525-2579 for your nearest RYOBI AUTHORIZED SERVICE CENTER to obtain replacement parts before attempting to assemble or use your router table. WARNING: To prevent accidental starting or electrical shock that could cause possible serious personal injury, assemble all parts to your router table before connecting it to power supply. Neither the router nor the table should be connected to power supply when you are assembling parts, making adjustments, installing or removing cutters, cleaning, or when not in use. WARNING: If any parts are damaged or missing, do not use your router table until the parts are replaced. Failure to do so could result in possible serious personal injury. 5 13 18 11 16 10 6 4 8 2 17 7 1 19 20 3 9 12 1. Fence assembly (1) 1/4-20 square nut (2) Fence lock knob (2) Guard post (1) Guard/dust cover assembly (1) Miter gauge bar (1) Miter gauge (1) Throat plate (5) 15 14 Fig. Operator's manual (not shown) (1) 22. Warranty registration card (not shown) (1) 17. Miter gauge knob (1) Page 7 ASSEMBLY WARNING: Your router or router table should never be connected to power supply when you are assembling parts, making adjustments, installing or removing cutters, cleaning, or when not in use. Disconnecting your router and router table will prevent accidental starting that could cause serious personal injury. Locate the two square nuts and two fence lock knobs. Position a square nut inside the channel located underneath the table. Insert the lock knob through the hole in the fence assembly and screw it into the square nut below. Repeat for the other side. LEG ASSEMBLY Place router table upside down on a flat, level surface, so that the front edge is closest to you. With the router table upside down, the leg with the rectangular cutout should be in the front left corner of the table. Align the four holes in each leg with the four corresponding threaded holes in each corner of the table. Use the hex wrench provided to secure each leg with four 1/4-20 x 1/2 in. socket head screws and four lock washers. Fig. 3 LOWER GUARD ASSEMBLY Locate the two gray lower guards. Position them around the throat of the table so that the three holes of each guard line up with the three threaded holes in the table. [. . . ] Periodically check all clamps, nuts, bolts and screws for tightness and condition. Make sure that the throat plate, guard/dust cover assembly and lower guards are properly positioned and securely attached. WARNING: Always begin any maintenance procedure by disconnecting the router and router table from the power supply to avoid risk of serious personal injury IMPORTANT Servicing of a tool with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest RYOBI AUTHORIZED SERVICE CENTER for repair. When servicing use only identical Ryobi replacement parts. [. . . ]