User manual RYOBI RY43006

[. . . ] ELECTRIC CHAIN SAW DOUBLE INSULATED RY43006 Your chain saw has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual before using this product. Thank you for buying a Ryobi product. SAVE THIS MANUAL FOR FUTURE REFERENCE TABLE OF CONTENTS n Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 n General Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] n Keep the unit running the entire time you are cutting, maintain a steady speed. n Allow the chain to cut for you; exert only light downward pressure. If you force the cut, damage to the bar, chain, or unit can result. n Release the switch trigger as soon as the cut is completed, allowing the chain to stop. If you run the saw without a cutting load, unnecessary wear can occur to the chain, bar, and unit. n Do not put pressure on the saw at the end of the cut. 12 n Always cut with both feet on solid ground to prevent being pulled off balance. n Do not cut above chest height, as a saw held higher is difficult to control against kickback forces. n Do not fell trees near electrical wires or buildings. n Cut only when visibility and light are adequate for you to see clearly. TREE FELLING Unusual Hazardous Tree Felling Conditions Do not fell trees during periods of high wind or heavy precipitation. WORK AREA PRECAUTIONS n Cut only wood or materials made from wood, no sheet metal, no plastics, no masonry, no non-wood building materials. n Never allow children to operate the saw. Allow no person to use this chain saw who has not read this Operator's Manual or received adequate instructions for the safe and proper use of this chain saw. n When felling a tree, keep everyone - helpers, bystanders, children, and animals - a safe distance from the cutting area. During felling operations, the safe distance should be a least twice the height of the largest trees in the felling area. During bucking operations, keep a minimum distance of 15 feet between workers. Trees should not be felled in a manner that would endanger any person, strike any utility line or cause any property damage. If the tree does make contact with any utility line, the utility company should be notified immediately. WARNING: Do not cut down trees having an extreme lean or large trees that have rotten limbs, loose bark, or hollow trunks. Have these trees pushed or dragged down with heavy equipment, then cut them up. WARNING: Do not cut trees near electrical wires or buildings. WARNING: Check the tree for damaged or dead branches that could fall and hit you during felling. 16 OPERATION WARNING: Periodically glance at the top of the tree during the backcut to assure the tree is going to fall in the desired direction. PLANNED LINE OF FALL WARNING: If the tree starts to fall in the wrong direction, or if the saw gets caught or hung up during the fall, leave the saw and save yourself!n Felling a tree - When bucking and felling operations are being performed by two or more persons, at the same time, the felling operation should be separated from the bucking operation by a distance of at least twice the height of the tree being felled. Trees should not be felled in a manner that would endanger any person, strike any utility line or cause any property damage. If the tree does make contact with any utility line, the utility company should be notified immediately. [. . . ] n From the finger-tight position, tighten the screw an additional 3/4 of a turn using a wrench. Fig. 43 TRANSPORTING AND STORING See Figure 44. n Do not store or transport the chain saw when it is running. The chain saw should always be idle before storing or transporting. [. . . ]