User manual RYOBI TS1351

[. . . ] (254 mm) Compound Miter Saw Model TS1351 - Double Insulated 33. 9 45 30 15 45 5 15 31. 62 30 22. 5 Your new Miter Saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance. WARNING: To reduce the risk of injury, the user must read and understand the operator's manual. Thank you for buying a Ryobi tool. SAVE THIS MANUAL FOR FUTURE REFERENCE . 5 30 1 31. 62 TABLE OF CONTENTS I I I I I I I I I I I Introduction and Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 14 ASSEMBLY TO INSTALL BLADE See Figures 15 and 16. SPINDLE LOCK BUTTON WARNING: A 10 in. (254 mm) blade is the maximum blade capacity of your saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. Larger blades will come in contact with the blade guards, while thicker blades will prevent the blade bolt from securing the blade on the spindle. Either of these situations could result in a serious accident and can cause serious personal injury. I Unplug your saw. WARNING: Failure to unplug your saw could result in accidental starting causing possible serious personal injury. I Loosen screw A on the blade bolt cover. I Rotate lower blade guard up and remove screw B. Rotate blade bolt cover up and back to expose the blade bolt. I Depress the spindle lock button and rotate the blade bolt until the spindle locks. I Using the wrench provided, loosen and remove the blade bolt. NOTE: The blade bolt has left hand threads. I Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade. 15 SCREW A SCREW B BLADE BOLT COVER LOWER BLADE GUARD WARNING: If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly. I Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 16. The double "D" flats on the blade washers align with the flats on the spindle. I Depress spindle lock button and replace blade bolt. Note: The blade bolt has left hand threads. Turn blade bolt counterclockwise to tighten. TO LOOSEN INNER BLADE WASHER WITH DOUBLE "D" FLATS FLAT (S) ON SPINDLE TO TIGHTEN BLADE BLADE BOLT OUTER BLADE WASHER WITH DOUBLE "D" FLATS Fig. [. . . ] If operation is dusty, also wear a dust mask. WARNING: Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc. They contain chemicals that can damage, weaken or destroy plastic. It has been found that electric tools are subject to accelerated wear and possible premature failure when they are used on fiberglass boats, sports cars, wallboard, spackling compounds, or plaster. The chips and grindings from these materials are highly abrasive to electric tool parts such as bearings, brushes, commutators, etc. [. . . ]