User manual RYOBI TS200

[. . . ] Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service. Please fill out and return the Warranty Service Registration Card so we can be of future service to you. Thank you again for buying Ryobi tools. SAVE THIS MANUAL FOR FUTURE REFERENCE 0 10 20 30 40 45 TABLE OF CONTENTS Table Of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury. OPTIONAL ACCESSORIES Optional accessories are available and may be purchased for use with your saw. They include table extensions, a stop block, and dust bag. The table extensions increase the work surface to 36 inches wide, providing improved support for cutting long workpieces. The stop block is useful as a stop for cutting multiple workpieces 7-1/8" 7-1/8" 3-3/8" 4-1/8" 4-1/8" 9-7/8" 9-7/8" 3-3/8" 18" 18" 9-3/4" 9-3/4" 7/16" DIA. HOLE 4-1/8" 4-1/8" 3-3/4" 3-3/4" 16-1/2" 16-1/2" 24" 24" Fig. 6 Page 11 ASSEMBLY WARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts to your saw completely before connecting it to power supply. Saw should never be connected to power supply when you are assembling parts, making adjustments, installing or removing blades, or when not in use. As mentioned previously your saw has been factory assembled and adjusted. The miter lock handle, work clamp, dust guide, and blade are the only parts that have to be installed. 20 10 0 10 20 30 40 45 TO LOOSEN TO TIGHTEN MITER LOCK HANDLE MITER LOCK HANDLE See Figure 7. To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threaded hole in the miter table control arm. Turn clockwise to tighten. CONTROL ARM MITER TABLE Fig. NOTE: The blade bolt has left hand threads. Wipe a drop of oil onto inner blade washer and outer blade washer where they contact the blade. LOWER BLADE GUARD NOTCH s LOWER BLADE GUARD BRACKET ION TAT RO s s s s Fig. 10 LOWER BLADE GUARD 45 s s PHILLIPS SCREW FLAT (S) ON SPINDLE BLADE BOLT COVER WARNING: TATION RO If inner blade washer has been removed, replace it before placing blade on spindle. Failure to do so could cause an accident since blade will not tighten properly. s Fit saw blade inside lower blade guard and onto spindle. The blade teeth point downward at the front of saw as shown in figure 11. RO INNER BLADE WASHER WITH DOUBLE "D" FLATS TI TA ON BLADE TO LOOSEN TO TIGHTEN OUTER BLADE WASHER WITH DOUBLE "D" FLATS Fig. 11 CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. The direction of blade rotation is also stamped with an arrow on the upper blade guard. The double "D" flats on the blade washers align with the flats on the spindle. Depress spindle lock button and replace blade bolt. [. . . ] Brush assembly is spring loaded and will pop out when you remove brush cap. Do not replace one side without replacing the other. Make sure curvature of brush matches curvature of motor and that brush moves freely in brush tube. Make sure brush cap is oriented correctly (straight) and replace. [. . . ]