User manual SABINE FBX SOLO 620 SL-620

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SABINE FBX SOLO 620 SL-620. We hope that this SABINE FBX SOLO 620 SL-620 user guide will be useful to you.

Lastmanuals help download the user guide SABINE FBX SOLO 620 SL-620.


Mode d'emploi SABINE FBX SOLO 620 SL-620
Download
Manual abstract: user guide SABINE FBX SOLO 620 SL-620

Detailed instructions for use are in the User's Guide.

[. . . ] OPERATING GUIDE SL-620 SM-620 INSIDE THIS GUIDE: About the FBX 2, 3 Quick-Start Operation 2 FBX-SOLO Controls 4, 5 Applications 6-8 Understanding Fixed & Dynamic Filters 9 Operating Instructions 10-12 Troubleshooting Tips 13 Product Specifications 14 Cautions 14 Warranty 15 FBX-SOLO Model SL-620 FBX-SOLO Model SM-620 CONGRATULATIONS!You now have the state-of-the-art in feedback control. The Sabine FBX-SOLO gives you automatic real-time feedback control for any channel on your mix. In setup and during the performance, it gives you more gain and increases the clarity of your mains and monitors. [. . . ] If you wish to use phantom power, you may enable the function by switching to "PHANTOM POWER - ON" on the back panel. The majority of low impedance balanced non-phantom-powered mics are wired to ignore phantom power. Check your microphone owner's manual for verification to avoid damage. Follow these steps to obtain the maximum gain before feedback without changing the tonal quality of your program. The following instructions are for using the SOLO on the mains. For use with monitors, substitute monitor send and master monitor control for input channel level fader and mixer master output. Be sure to turn off the mains when initializing the SOLO in your monitor system. Place the speakers and microphones in the positions where they will be used during the program. Avoid placing microphones directly in front of speakers. Set the mixer master output, all channel level faders, and the monitors to minimum. Turn on the mixer, any signal processing equipment, and finally the power amp. Press the SOLO's RESET button until the LEDs stop flashing to clear out filters set previously. If you are using a graphic EQ, adjust it only for the desired tonal qualities. The "BY" LED will light green to indicate the SOLO is in active mode and red if it is in bypass mode. Turn the SOLO's clip level adjust to the two o'clock position. Set the mixer master output to a nominal level, and lower all channel levels to minimum. Slowly raise the channel level fader for the channel being set until feedback occurs. The SM should quickly remove the feedback. The first FILTER LED will then blink to indicate a filter has been set. Keep raising the channel level fader slowly until all FIXED FILTERS and one dynamic filter is set. Any uninitialized dynamic filters will be set later if feedback occurs during the program. Now lower the channel level fader slightly so that the system is not on the verge of another feedback point. This is the maximum volume level the SM will be able to provide. [. . . ] 13301 HIGHWAY 441 ALACHUA, FL 32615-8544 USA including therewith a complete, detailed description of the problem, together with a legible copy of the original PROOF OF PURCHASE and a complete return address. Upon Sabine's receipt of these items: If the defect is remedial under the limited warranties and the other terms and conditions expressed have been complied with, Sabine will provide the necessary warranty service to repair or replace the product and will return it, FREIGHT COLLECT, to you, the purchaser. Sabine's liability to the purchaser for damages from any cause whatsoever and regardless of the form of action, including negligence, is limited to the actual damages up to the greater of $500. 00 or an amount equal to the purchase price of the product that caused the damage or that is the subject of or is directly related to the cause of action. Such purchase price will be that in effect for the specific product when the cause of action arose. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SABINE FBX SOLO 620 SL-620

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual SABINE FBX SOLO 620 SL-620 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag