User manual SAECO BP 56

[. . . ] 10 3. 2 Installing the CHANGE-GIVING COINER . . . . . 11 3. 3 Installing the BANKNOTE READER . . . . . . . . . . . . . . . 12 The CPU card shown in figure 1, illustrates the connections for the accessories and payment systems described below in this manual. 1 2 3 4 5 6 7 8 9 10 Parallel banknote reader 12/24V DC MDB Executive and BDV Saeco Card Parallel coiner 24V DC Parallel coiner 12V DC Token box 12V DC Interface connector 7P/8P Clock module (TIME KEEPER) Nation key / programming key 3 1 8 2 9 3 5 6 4 7 10 Fig. [. . . ] " It is possible to transfer all the data; SYSTEM MANAGEMENT. " It is possible to transfer all the data, with the exception of the code of the SERIAL NUMBER and of the PASSWORD. When the device is next turned on, the display will show the message: "TRANSFER KEY - RIGHT MODEL", if the key connected corresponds to the vending machine model (example A), or "TRANSFER KEY - WRONG MODEL", if the key connected does not correspond to the vending machine model (example B). In case A, it is possible to transfer the parameters from the vending machine to the programming key and vice-versa. A DATA TRANSFER SAVING DATA TRANSFER KEY RIGHT MODEL DATA TRANSFER KEY -> VMC DATA TRANSFER READING DATA DATA TRANSFER VMC -> KEY DATA TRANSFER WRITING DATA The connector (10 - Fig. 1) for the programming key is the same as that for the nation key. To connect up the programming key, proceed as follows: - open the front door of the vending machine; - slide out the nation key from the connector (10 ­ Fig. 1); - connect up the programming key to the same connector as the nation key (Fig. 3). In case B, it is only possible to transfer the parameters from the vending machine to the programming key. B TRANSFER KEY WRONG MODEL DATA TRANSFER VMC -> KEY DATA TRANSFER WRITING DATA NOTE To go back to the previous menus, press the back to the previous levels, press the key. key; to go Any errors that may occur during the data transfer phase are displayed with the message "TRANSFER KEY - ERROR IN KEY DATA". Should this message appear, repeat the data transfer procedure; if the error continues to appear, contact an AUTHORISED CUSTOMER SERVICE CENTRE. Important When the data transfer has been completed, reinsert the nation key as per the instructions given in the operation and maintenance manual for the automatic vending machine BP 56 e BP 36. Fig. 3 6 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 3 3. 1 PAYMENT SYSTEMS Installing the SAECO CARD Maintenance Technician - apply the antenna (B ­ Fig. 4) to the protective panel of the operating instructions label (Fig. 6); This operation should be carried out by the Maintenance Technician. 4) A 1 universal module; B 1 antenna; C biadhesive plate; D protective linen band; E 1 adhesive label for the reading position of the SAECO CARD; F flat cable. Fig. 6 F E B C A apply the linen cloth (D ­ Fig. 4) so as to completely protect the antenna (Fig. 4 Installation Before installing, make sure that the TIME KEEPER clock module is fitted (point 2. 1). Then, proceed as follows: - open the front door of the vending machine; apply the biadhesive plate (C ­ Fig. 5 Espresso Italia PTY LTD www. espressoitalia. com. au 7 Freecall 1300 660 976 English - On the BP 56 position the universal module (A ­ Fig. 4) by hooking it onto the 4 supporting pins (Fig. 8); - On the BP 56 connect the flat cable (F - Fig. 4) to the connector of the universal module (Fig. [. . . ] 20 re-attach the upper panel of the keyboard and reconnect the cable to the connector (Fig. 23 Espresso Italia PTY LTD www. espressoitalia. com. au 13 Freecall 1300 660 976 English - connect the BANKNOTE READER cable to the connector (1 ­ Fig. 24); Important The programming procedures are shown in the operation and maintenance manual for the automatic vending machine BP 56 e BP 36. In the event that both a CHANGE-GIVING COINER and a BANKNOTE READER must be fitted to the same vending machine, the latter should be installed in the position of the instructions panel. [. . . ]