User manual SAECO D.A. COMBISNACK

[. . . ] Vending machine ACCESSORIES AND PAYMENT SYSTEMS D. A. COMBISNACK Type: D. A. COMBISNACK Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 USE AND MAINTENANCE English Contents 123456789DIAGRAM OF CONNECTIONS TO THE KEYPAD BOARD/CPU:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 38 Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 7- WATER SOLENOID VALVE KIT - Open the upper door and loosen the screw (fig. 42) fixing the block support plate. It is possible to brew hot water alone by installing the required kit Assembly kit (fig. 1 OR, pipe clamp and 1/8" H4, 5 nut c. 43). Installation Remove the machine rear panel (fig. 40) by untightening the screws and disconnecting the ground wiring placed on the machine. fig. 40 Unscrew the cap inserted on the solenoid valve block (fig. 41) and hold the latter to avoid any excessive stress to the block support plate. Loosen the two screws fixing the block support plate (fig. 41 Espresso Italia PTY LTD www. espressoitalia. com. au 13 Freecall 1300 660 976 English - Screw the nut and fix the OR (ref. Remove the block support from its seat and screw the solenoid valve in the hole (fig. 45) previously cleared from its cap (fig. The solenoid valve must be placed with fastons upwards Reinstall the block support in their seat and tighten the screws. - Insert the pipe clamp (ref. 48) at the solenoid valve outlet and position the pipe retaining spring. Slide the other end of the pipe inside the assembly plate passage hole (ref. Reassemble the machine rear panel. - d fig. 46) that fastens the two unused cables. - Fasten the pipe end with fitting to the spout (fig. 49 To brew hot water alone, it is necessary to set the beverage associated with the required key according to the following parameters: - Connect the 2 free cables to the solenoid valve taking care to insert the red cable on the left and the white cable on the right. Parameter Sequence Soluble product quantity 1 H2O soluble product quantity 1 % soluble 1 sugar Value 0001 0 Set the required water quantity 100 0 fig. 47 14 Close the vending machine upper door. Espresso Italia PTY LTD www. espressoitalia. com. au Freecall 1300 660 976 English 8 - SUGAR COIL KIT This kit allows the sugar door opening only when required, since an electromagnet controls it. This prevents any sugar grain from accidentally falling when the "without sugar" option has been selected. - Disassemble the sugar-dispensing channel (Fig. 1 1 2 1 1 1 two-pin connector connecting rod M3x6 screws, 1 M3x8 screw and 1 M3 nut relay electromagnet spring sticker fig. 52 - c d - Install the connecting rod (ref. 54) in order to seal the hole located on the machine housing. a b e f fig. [. . . ] 16-pole flat cable 3 adhesive spacers 10-pole flat cable Interface card To - properly use the programming key, do as follows: open the vending machine front door; insert the programming key into the connector (ref. switch on the vending machine. a b Installation c d fig. 95 The copy key presence enables the following menu display: Open the upper door and slide the keypad carter up. 95, b) into the special holes of the interface card (fig. [. . . ]