User manual SAMMY DEMOLISH FIST

[. . . ] 1 1 2 4 5 6 RED ORG ORG/ GRN +5VDC, 2P POT. (X) PIN 1 COLOR RED FUNCTION +5VDC, 1P POT. P5 - 13 PIN CONNECTOR (MALE) 1 PIN 1 2 COLOR BLK BLK GRN/WHT GRN ORG/ ORG RED RED FUNCTION GND, 1P POT. +5VDC, 2P POT. J1 - 5 PIN CONNECTOR ( MOLEX/FEMALE) PIN 1 3 4 5 PIN 1 2 3 5 6 COLOR RED BLK VIO VIO/WHT COLOR GRN/BLU GRN/YEL ORG BLK/YEL BLK/YEL FUNCTION +5VDC 1 GND 1P COIL PULSE 2P COIL PULSE FUNCTION 1P COIL 2P COIL +21VDC, COIL GND, COIL GND, COIL 7 6 5 1 1 13 3 4 5 6 10 11 PIN 1 4 COLOR GRN/YEL GRN/BLU FUNCTION 2P COIL 1P COIL J2 - 6 PIN CONNECTOR ( MOLEX/FEMALE) P3 - 7 PIN CONNECTOR (MALE) 1 NOTE: P4 - 15 PIN and P3 - 10 PIN Connector are using for REVOLUTION X. P5 - 13 PIN and P10 - 10 PIN Connector are using for TERMINATOR 2. PIN 9 10 10 COLOR GRN/YEL GRN/BLU FUNCTION 2P COIL 1P COIL P10 - 10 PIN CONNECTOR ORANGE BLACK/YELLOW 9 7. [. . . ] · SOLENOID COIL INTERFACE BOARD Put the DEMOLISH FIST Solenoid Coil Interface Board nearby the Main P. C. Board. NOTE: The DEMOLISH FIST game does not need the Sound Board. If your game is a REVOLUTION X, you have to take off the old Sound Board from your REVOLUTION X cabinet when you remove the old P. C. Board. 3. Connect the INTERFACE HARNESS NOTE: There are two types of setting styles in these instructions. If your game is REVOLUTION X, see WIRING INSTRUCTIONS FOR REVOLUTION X (Page 11). If your game is TERMINATOR 2, see WIRING INSTRUCTIONS FOR TERMINATOR 2 (Page 12). 10 WIRING INSTRUCTIONS FOR REVOLUTION DEMOLISH FIST SOLENOID COIL INTERFACE BOARD JAMMA 7 J1 - 5 6 DEMOLISH FIST MAIN P. C. BOARD CN2 - 8 J2 - 6 1 P4 - 15 3 2 P3 - 7 DEMOLISH FIST INTERFACE HARNESS 5 Power Supply Box P6 - 7 PIN, PIN Revo-X Gun Coil Driver Board 4 P5 - 4 PIN, PIN 1: Connect the JST - 8 PIN Connector of the DEMOLISH FIST Interface Harness to the CN2 - 8 PIN Sub Connector on the DEMOLISH FIST Main P. C. Board. 2: Pull off the P3 - 7 PIN Connector from the REVO-X Gun Coil Driver Board. Then connect the P3 - 7 PIN Connector to the P3 - 7 PIN of the DEMOLISH FIST Interface Harness. 3: Connect the P4 - 15 PIN of the DEMOLISH FIST Interface Harness to the P4 - 15 PIN Connector which had been connected on the REVO-X Main P. C. Board. 4: Connect the BLACK/YELLOW wire (GND) of the DEMOLISH FIST Interface Harness to the #1 Pin of the P5 - 4 PIN Connector from the REVO-X Gun Coil Driver Board with the Tap Connector. 5: Connect the ORANGE wire (+21VDC) of the DEMOLISH FIST Interface Harness to the #1 Pin of the P6 - 7 PIN Connector from the REVO-X Gun Coil Driver Board with the Tap Connector. * Press the 1P Start Button or the 2P Start Button. Use this screen to check the size of picture. The CROSS HATCH test pattern has a White grid on a Black background. Check following: - The grid line should be straight, and the lines should not have excessive pincushion or barrel distortion. - "Out" line of grid line is the same size as "Out" line of game screen. So, "Out" line should be able to be seen with no overflow of grid lines on screen. If these are not as above, adjust the Monitor as described in the Monitor's manual. * Pull the TRIGGER or the PUMP SWITCH or the 2P Start Button. You can exit and go back to the TEST MENU screen. You can go to next test (DIP SWITCH). 2. DIP SWITCH Use this screen to see how all the DIP Switches are set. [. . . ] You can check each sound in this game. SOUND SOUND CODE 00H xxxx STOP SOUND xxxx SELECT START : TRIGGER : STOCK NEXT 1P START BUTTON EXIT 2P START BUTTON 6. MEMORY TEST Use this screen to check RAM and ROM on the Main P. C. B. will automatically check them when you enter this screen. The extent of this warranty applies to all electronic assemblies only, and does not include lamps and fuses. [. . . ]