User manual SAMMY KEY CATCHER

[. . . ] · Press and hold PUSH BUTTON 1 (UP) to move the arm up. NOTE: When player releases the PUSH BUTTON, the arm will not move any more. · Press and hold PUSH BUTTON 2 (SIDE) to move the arm sideways. NOTE: When player releases the PUSH BUTTON, the arm will not move any more. · The arm automatically grabs the prize. Press and hold PUSH BUTTON 1 (UP) to move the arm up. 2. Press and hold PUSH BUTTON 2 (SIDE) to move the arm sideways. 4 3. GAME PRIZE ARM SENSOR CLAW (L) CLAW (R) HOW THE CLAW SENSES THE PRIZE After Prize breaks the SENSOR LINE between CLAW (L) and CLAW (R), both Claws start to close and try to grab Prize. SENSOR LINE HOW TO FILL PRIZE 1 Turn off MAIN POWER SWITCH. [. . . ] If you hit this switch with TEST SWITCH (L) at the same time, you will go to the test mode. When you get any errors, stop error noise by first hitting SERVICE SWITCH and then hit this switch. The errors will be cleared. TEST SWITCH (R): 10 6. DIP SWITCH TABLE There are DIP SWITCH (L) and DIP SWITCH (R) on the SWITCH BOARD. (See Page 10) NOTICE Before you change any DIP SWITCH setting, turn off the Main Power! NOTE: DIP SWITCHES (L)/(R) FUNCTIONS DIFFICULTY LEVEL * RANDOM GRAB Each arm has its own Dip Switch Adjustment. SETTING HARDEST HARD NORMAL EASY EASIEST EASY NORMAL HARD 1 COIN 1 CREDIT 1 COIN 1 CREDIT 1 COIN 2 CREDITS 1 COIN 3 CREDITS 1 COIN 4 CREDITS 2 COINS 1 CREDIT 2 COINS 1 CREDIT 3 COINS 1 CREDIT 3 COINS 1 CREDIT 4 COINS 1 CREDIT 5 COINS 1 CREDIT 5 COINS 1 CREDIT 1 2 3 4 5 6 7 8 * SAME GRAB OFF ON OFF OFF ON OFF ON OFF ON OFF OFF ON OFF OFF ON ON OFF ON ON ON ON ON OFF ON ON ON ON OFF ON ON OFF OFF OFF OFF ON OFF ON OFF OFF ON ON OFF ON ON OFF OFF OFF ON ON OFF OFF OFF OFF ON ON ON OFF OFF OFF OFF OFF ON ON ON ON ON ON ON OFF ON OFF OFF OFF OFF ON OFF ON ON OFF ON COIN CHUTE "FACTORY INSTALLED" SETTING * RANDOM GRAB: * SAME GRAB: To be used with prizes of various or shapes. You can select the claws closing on each grab. The machine always closes the claws at the same width. 11 7. ERROR When the machine gets any errors, the LED DISPLAYS on the control panel show an error number and an error letter. After you stop the error noise by hitting the SERVICE SWITCH, you have to check which machine part has the error. NOTICE Hit the SERVICE SWITCH and stop the error noise!You can not stop the error noise by hitting the TEST SWITCH. LED (L) LED (R) ERROR ARM DRIVE MOTOR/ FORWARD-BACK ARM DRIVE MOTOR/ UP-DOWN ARM DRIVE MOTOR/ LEFT-RIGHT ARM DRIVE SHAFT SENSOR PRIZE PAYOUT SENSOR CONTENTS This drive motor has a problem. Check around the arm which is stuck to correct. Press one of the TEST SWITCHES and the error will be cleared. Check around the arm which is stuck to correct. Press one of the TEST SWITCHES and the error will be cleared. Check around the arm which is stuck to correct. Press one of the TEST SWITCHES and the error will be cleared. Check the harness and the sensor around the arm. Press one of the TEST SWITCHES and the error will be cleared. A prize is left or stuck in the payout door. [. . . ] ·: No number · The number changes by pressing PUSH BUTTON 1 (UP). · Each part will move by pressing PUSH BUTTON 2 (SIDE), LED DISPLAY 31· 32· 33· 34· ARM MOVEMENT LEFT & RIGHT UP & DOWN FORWARD & BACK CLAWS OPEN & CLOSE * Press one of the TEST SWITCHES in this menu and you will go to #4/SENSOR TEST. 4 SENSOR TEST · The LED DISPLAY shows "4". · When you break the sensor line between the claws with your hand, PUSH BUTTON 1 (UP) · · When you break the sensor line in the prize door duct by your hand, the prize door light will light a few seconds and the prize payout meter will count. * Press one of the TEST BUTTONS in this menu and you will go to #5/COIN TEST. [. . . ]