User manual SAMMY TROPHY HUNTING CONVERSION KIT

[. . . ] GAME PLAY Trophy Hunting is a sports hunting game that has an exciting COMPETITION MODE. Two players can play at the same time in competition mode which is a Sammy USA "EXCLUSIVE"!? Insert coin(s) and press Hunter 1 or Hunter 2 button to start game. Use Sammy 27" Shotgun to (Pump the Shotgun before you shoot the screen each time. ) Select one of 6 states. [. . . ] Use a hex wrench to tighten screws. IF YOU WANT TO INSTALL A HAND GUN: You can use a HAND GUN instead of the original pump action gun for this game. *WARNING* Be absolutely sure that the connector for the hand gun matches exactly the pin position for CN5 (1P Gun) and CN7 (2P Gun) as shown on page 4. Connect 1P Gun connector to CN5, 2P Gun connector to CN7 and turn on Dip switch 2, #8. See page 5 for Dip switch table. 11 · INSTRUCTION DECAL SHEET Put "PUMP BEFORE SHOOTING" Decal Sheet on the front glass of the monitor. MONITOR PUMP BEFORE SHOOTING DECAL AAMA STICKER · AAMA "ANIMATED VIOLENCE MILD" STICKER Place AAMA sticker on the upper left hand side corner of the marquee. ANIMATE VIOLENCE MILD Remove old P. Connect the HARNESSES · JAMMA HARNESS Connect the JAMMA Harness to the edge connector on the TROPHY HUNTING Main P. C. BOARD. · GUN HARNESS Connect the Gun Harness to the Gun Connectors located on the Main P. C. Board components side, at CN5 & 6 and CN7 & 8 connectors on the P. C. Connect Gun Connector to CN5 & 6 and CN7 & 8, correctly, as shown below. 10 pin connector from GUN Assy (1P) 10 pin connector from GUN Assy (2P) CN 5 10 1 CN 6 CN 7 10 1 CN 8 Connectors on the Main PCB Connectors on the Main PCB 12 10. TEST MODE Entering the TEST MODE If you need to check the condition of the game circuitry and controls, you can use the TEST MENU. Turn ON "DIP SWITCH 1, #8" and re-power on the game. The game will go into TEST MODE (diagnostics) and the screen appears as follows: Select TEST Use this screen to choose which of the 7 screens you want to see. To check the functioning of each switch, activate it and watch the corresponding OFF letters change to ON. If the ON and OFF letters do not appear correctly, check the Harness connections and Switches. * Press START button and Gun trigger simultaneously to exit. I/O TEST COIN A COIN B SERVICE TEST 1P GUN START PUMP TRIGGER : : : : OFF OFF OFF OFF 2P GUN START PUMP TRIGGER : OFF : OFF : OFF : OFF : OFF : OFF PRESS START & GUN TRIGGER TO EXIT 5. SOUND TEST Use this screen to check all game sounds. (Hunter 1 = forward, Hunter 2 = Back) Then pull the TRIGGER. * Press START button and Gun trigger simultaneously to exit. SOUND TEST SOUND CODE 000 BLAK_SHOT PRESS START BUTTON TO CHOOSE PRESS GUN TRIGGER TO PLAY PRESS START & GUN TRIGGER TO EXIT 6. MEMORY TEST Use this screen to check RAM and ROM on the Main P. C. B. will automatically check them when you enter this screen. If there are no problems, the word OK will appear on screen. If you get the word ERROR, check the mounting of RAMs or ROMs on the Main P. C. B. and if ERROR reappears, it needs to be replaced. MEMORY TEST WORK RAM : OK BACKUP RAM : OK ROM (U06) ROM (U07) : OK : OK * This mode will automatically exit after testing is finished. 14 7. [. . . ] There are no additional warranties which extend beyond those limited warranties described above. The limited warranties described above shall be in lieu of any other warranty, express or implied, including but not limited to any implied warranty of merchantability or fitness for a particular purpose. Return Merchandise Authorization 1. Contact your authorized Sammy USA distributor to receive a Return Merchandise Authorization for return. You must obtain RMA numbers from Sammy USA Corporation through an authorized Sammy USA distributor. [. . . ]