User manual SAMSON SMIX

[. . . ] S Class Signal Processors 0 10 0 10 0 10 0 10 5 CHANNEL MIXER Table Of Contents Introduction and Features Front and Rear Panel Layout Operating the S mix Setting up the S mix Connecting the Input Signals Typical Set-up Creating a mix Specifications Wiring Guide 3 4 5 6 7 7 8 8 Copyright 2003, Samson Technologies Corp. Printed January 2003 Samson Technologies Corp. Box 9031 Syosset, NY 11791-9031 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 516-364-3888 www. samsontech. com A K-TEAM P R OD U C T IO N S mix Introduction and Features Thank you for purchasing the S mix, miniature mixer by Samson Audio! [. . . ] TRS OUTPUT - Left and Right main mix OUTPUT on TRS (TIP/RING/SLEEVE) connectors. 4 1 L & R RCA OUTPUT - Left and Right main mix OUTPUT on RCA connectors. CHANNEL 4/5 VOLUME - Control knob used to adjust the level of inputs 4 and 5. 5 2 6 Rear Panel Layout C CHANNEL 3 INPUT- XLR mic-level input for connecting standard microphones. DC POWER INPUT- Connect the supplied power adapter here. CHANNEL 4/5 INPUTS- RCA inputs for stereo line level signals. POWER LED - Red LED will illuminate when power is on indicating the S mix is ready for operation. D E A CHANNEL 1 INPUT- 1/4-inch input for connecting Line/Instrument level signals. F B CHANNEL 2 INPUT- 1/4-inch input for connecting Line/Instrument level signals. 4 Operating the S mix Setting up the S mix The basic procedure for setting up and using your S mix miniature mixer takes only a few minutes. Remove all packing materials (save them in case of need for future service) and check to make sure that you remove the supplied AC/DC power adapter. Note: Before plugging in and turning on, remember the "last on, first off" rule of power amplifiers and powered speakers. When powering up your system, be sure that all the wires are connected, turn your mixer and any other outboard gear on, and then last, turn your power amplifier or powered speakers on. When powering down, turn your power amplifier or powered speakers off first and then your mixer and outboard gear. · Connect the supplied AC/DC adapter to the DC Input on the rear panel of the S mix (Figure 1), then plug the adapter into any standard AC outlet. Set the S mix volume control knobs to the following default positions: All off. (Figure 2): Connect the S mix outputs to your power amp or powered speaker using the Left and Right RCA OUTPUT, or the 1/4" TRS jack OUTPUT connectors. Below is a wiring diagram for the 1/4" TRS stereo OUTPUT connector (Figure 3). Figure 2 Figure 1 · · Figure 3 5 Operating the S mix Connecting Inputs Signals to the S mix The S mix provides the capability of receiving signals from microphone, instrument and line level devices. Super-Z Line Inputs Channel 1 and 2 inputs are Super-Z, line/instrument level inputs on 1/4-inch phone connectors. The inputs can accept the signal from a variety of instruments level sources like those from the outputs of guitars, bass guitars and clavinets, and line level signals like those from the outputs MIDI keyboards, signal processors and drum machines, to name some. Mic input The channel 3 Mic input will accept signal from any low impedance microphone. [. . . ] You may want to go back and slightly raise or lower an individual channel until you have set the balance between all the connected inputs. Then, you have your perfect mix! 7 S mix Specifications Frequency Response THD+N Noise Level Microphone Input Super-z Line Input Left and Right Inputs Left and Right Outputs Wiring Guide 10 Hz to 95 kHz <0, 005 % -105 dBu XLR, balanced 1/4" jack unbalanced RCA, unbalanced input RCA, unbalanced output S mix Specifications - continued Mono, Instrument Level Output Input Impedance (Inst Chn. ) Output Impedance Maximum Input Level Power Supply Dimensions Weight 1/4", unbalanced 1 Meg Ohm 100 Ohm +21 dBu 18 V DC 5. 65" L x 4. 13" W x 2" H (144mm L x 105mm W x 51mm H) 16. 5 oz. , 419 gm. Samson Technologies Corp. Box 9031 Syosset, NY 11791-9031 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 516-364-3888 www. samsontech. com [. . . ]