User manual SAMSUNG SYNCMASTER 320MP-3

[. . . ] SyncMaster 320MX-3, 320MXN-3 320MP-3, 320MPN-3 LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Prohibited Do not disassemble Do not touch An administration fee may be charged if either · (a) an engineer is called out at your request and there is no defect in the product (i. e. [. . . ] Manually adjust the backlight for the selected display. If Auto Lamp Control is adjusted, Manual Lamp Control will automatically switch to Off. Ambient Light: Ambient Light detects ambient light intensity and automatically adjusts the screen brightness of all the LFDs in the same serial chain. 3. 6. 12 Tool Settings 1 2 3 4 1 Security Panel Control Turn on or off the screen of a display device. Remote Control Enable or disable the remote control. 2 Reset Reset Picture Reset the screen settings. Reset All Reset the screen, sound and system settings at the same time. 3 Edit Column Select the items you want to display in the list of sets. 4 Information View the program information. 3. 6. 13 Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. Move the arrow to customize the size of the program window. Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 2 Right-click and select Group>Edit in the display device list section on the left side of the program window. In the Edit Group window displayed, click Add on the sub level or Add on the same level. Add on the sub level: Create a sub-group under the selected group. Add on the same level: Create a group on the same level as the selected group. The Add on the same level button is enabled only if at least one group is created. 3 Enter the group name. Deleting Groups 1 2 Select a group name, and click Edit. In the Edit Group window displayed, click Delete. 3 Click Yes. The group will be deleted. Renaming Groups 1 2 Select a group name, and click Edit. In the Edit Group window displayed, click Rename. 3 If a cursor appears in the old group name, enter a new group name. Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear. 3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. Device Group: Select a group. Date&Time Instant Execution: Run the schedule immediately. Timer Set the date, time and interval to run the schedule. Action: Select a function that will activate at the specified time and interval. Schedule Modification To modify a schedule, select the schedule and click Edit. Deleting a Schedule To delete a schedule, select the schedule and click Delete. Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. Check that the display ID is within the range of 0 and 99. (Change the ID using the Display menu. ) For a display that supports the ID in a range of 0 to 99, the ID should be set between 0 and 99. 3. The display you want to control does not appear on the other Control Info Grids. The following message appears repeatedly. Check that the display is powered on. (See the power status in the system information chart. ) Ensure you select the input source the display is connected to. [. . . ] The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. [. . . ]