User manual SAMSUNG 35MM D-XENON

[. . . ] Storage and mildew prevention · Take the lens out of the protective case or camera bag, and store it in a dry, well-ventilated place. · Avoid storing the lens in a poorly ventilated location such as a closet, wardrobe, drawer, vehicle, or where insect repellent or medicine is kept. · Avoid storing the lens in areas of high temperature and humidity, where there is a risk of mildew growth. Store the lens with a desiccant in a dry cabinet, airtight container, or plastic bag. [. . . ] When Zoom lenses with power zoom function are used on the SAMSUNG KAF2-mount camera, the camera features a Power Zoom system. Mounts of Lenses without the power zoom function are KAF. KAF mount KAF2 mount AF coupler Lens-information contacts Power zoom contacts 5 Lens Mount Compatibility D-XENOGON lens mount compatibility chart is shown below. KAF2-mount which is equipped with Power contacts AF coupler Lens information contacts CAUTION: Be careful not to damage or dirty the lens-information contacts and AF coupler on the mount surfaces of the camera and lens. Otherwise, failure or malfunctionmay occur. KAF-mount which is equipped with AF coupler Lens information contacts KA-mount which is equipped with Lens information contacts K-mount (base mount) 6 MOUNTING AND REMOVING THE LENS 1 2 1. To mount the lens on the camera body Memo: · · Attach the lens while aligning the red dots on the lens and body, then turn the lens clockwise until it clicks in place. Do not hold down the lens unlock button while mounting the lens, otherwise the lens will not be properly mounted. After mounting the lens, gently turn the lens counterclockwise to make sure it is locked in place. Hold down the lens unlock button on the camera body and turn the lens counterclockwise. 7 2. To remove the lens LENS CAP Take off the lens cap by pressing the two tabs inward as shown above. 2. Memo: · When not using the lens, be sure to attach the lens cap. 8 FOCUSING 1 Changing the Focus Mode Use the camera' focus mode switch to change between the autofocus mode (SAF, s CAF) and manualfocus mode. For details, refer to your camera' manual. Using Autofocus Set the camera' focus mode to autofocus (SAF, CAF). Press the shutter button s halfway to autofocus. 9 Focusing with the OK Button With the GX-1S/1L camera set as explained below, auto focusing by pressing the shutter button halfway will be disabled and the OK button can be used instead to auto focus. On the [C Custom menu], select [Enable AF] for [OK btn when shooting]. Focusing with the AF Button With the GX-10 camera set as explained below, auto focusing by pressing the shutter button halfway will be disabled and the AF button can be used instead to auto focus. On the [CUSTOM1 MENU] menu, select [Enable AF] for [AF Button Function]. 2. Memo: · For details on the setting procedure, refer to the camera's instruction manual. CAUTION During autofocusing, the focusing ring will rotate. To prevent malfunction, do not touch the focusing ring during autofocusing. 10 2 2. Using Manual Focus Set to MF with the camera's focus mode, and turn the focusing ring to focus manually. 11 FOCUSING 7 2 3 2 ft 1 0. 7 0. 5 m A 22 16 11 8 5. 6 4 2 In auto focus mode You can adjust focus on the subjects automatically by pressing the shutter button halfway. In manual focus mode You can adjust focus on the subjects by turning the focusing ring manually. During autofocusing, the focus ring will rotate. To prevent malfunction, do not touch the focus ring. 12 APERTURE CONTROL 7 2 3 1 ft m 7 2 3 1 ft m A 22 16 11 8 5 . 6 4 A 22 16 11 8 5. 6 4 2 Setting the aperture to "A"(Auto) Turn the aperture ring to align the aperture-A index with the line while depressing the Aperture-A-lock button. The aperture ring can be released from "A" in the same manner to set your desired f-stop manually. 13 ATTACHING THE LENS HOOD In order to avoid the deterioration in image quality from internal reflection, use of the lens hood is recommended. The lens hood image can be diifferent depending on the lens hood type. Lens hood attaching index When attaching the lens hood, align the index on the lens hood with the attaching index on the lens, and push both parts straight toward each other. Attach the lens hood on the lens by turning the hood in the clockwise direction to lock it as viewed from the front of the lens until it clicks into position. 2. [. . . ] Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]