User manual SAMSUNG DV405ETPASU TROUBLE SHOOTING GUIDE

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

Sponsored Links

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual SAMSUNG DV405ETPASU. We hope that this SAMSUNG DV405ETPASU user guide will be useful to you.

Lastmanuals help download the user guide SAMSUNG DV405ETPASU.


SAMSUNG DV405ETPASU TROUBLE SHOOTING GUIDE: Download the complete user guide (6955 Ko)

You may also download the following manuals related to this product:

   SAMSUNG DV405ETPASU (12280 ko)

Manual abstract: user guide SAMSUNG DV405ETPASUTROUBLE SHOOTING GUIDE

Detailed instructions for use are in the User's Guide.

[. . . ] Invalid heating Temp in running the dryer Running the dryer with door open Action Taken Check for: - Clogged lint screen. Check for: - Not using regular power source frequency - Invalid power frequency sense circuit Check for: - Check PCB and Wire harness. HE dE dF Invalid door state for more than 256 milliseconds bE2 Invalid state of key circuit short for 30 secs FE Invalid power source Frequency 2E Electronic Control Problem (Over Voltage Error) Electronic Control Problem (Communication Error) Invalid state of Eeprom communication AE Et 2 (Technical)DV405-02365H-02_EN. [. . . ] Definition of Data Display Mode: - Display Mode 1 : Temperature data - Display Mode 2 : Average Touch Sensor data for 1 minute - Display Mode 3 : Average Temperature data for 1 minute 4 (Technical)DV405-02365H-02_EN. Indd 4 2012-06-19 �� 1:25:53 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. TROUBLE DIAGNOSIS - As the micom dry machine is configured of the complicate structure, there might be the service call. Below information is prepared for exact trouble diagnosis and suitable repair guide. Caution for the Repair and Replacement Please follow below instruction for the trouble diagnosis and parts replacement. 1) As some electronic components are damaged by the charged static electricity from the resin part of dryer or the human body, prepare the human body earth or remove the potential differ ence of the human body and dryer by contacting the power supply plug when the work contacting to PCB is executed. B assembly by the wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally. Indd 5 2012-06-19 �� 1:25:54 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. No Problem What To Do • • • • 1 Will Not Start or Run • • • • • • • • • • • • - - - • • 5 Blows fuses or trips circuit breaker (Gas Model) All wires are hooked up to their corresponding terminals. (Rotor winding , stator winding , generator) Is the motor protector normal?If the dryer is drawing amperages above this, then the house wiring, fuse box or circuit breaker is suspected to be at fault. 2 Motor runs/ tumbler will not turn Runs a few minutes and then stops 3 4 Blows fuses or trips circuit breaker • • • 6 Will not heat (motor runs) Open heating element. When the dryer is operated on a heat setting, the igniter should be energized and burner shall fire within 45 seconds at 120 VAC. The failure of a component in this system will usually be indicated by one of three symptoms: 6 7 Will Not Dry Gas Model Poor Gas Ignition (Technical)DV405-02365H-02_EN. Indd 6 2012-06-19 �� 1:25:54 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. No Problem What To Do If the igniter does not heat up, remove power and using an ohmmeter, check the following: • Open flame sensor The igniter does not • Open igniter 8 glow • Shorted booster coil • Open wiring • Bad motor switch ( Neutral supply) • No power from control ( L1 supply) If the igniter heats up but the main burner flame is not ignited, remove power and using an ohmmeter, check the following: Igniter glows - No gas • Open secondary coil 9 ignition • Open holding coil • Open wire harness • Stuck flame sensor (Stuck closed) If a normal ignition takes place and after a short while the flame goes out, check for the following: • Radiant sensor contacts opening prematurely. [. . . ] Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Insert the tab of the terminal block cover into your Dryer’s rear panel slot. If converting from a 4-wire electrical system to a 3-wire, the ground strap must be reconnected to the terminal block support to ground the Dryer frame to the neutral conductor. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SAMSUNG DV405ETPASU

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SAMSUNG DV405ETPASU will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag