User manual SAMSUNG MWR-AH01

[. . . ] x Do not use inflammable gases near the remote controller. x Do not spill water into the wired remote controller. x Do not operate the remote controller with wet hands. x Do not install the remote controller in a location where it will come into contact with the combustible gases, machine oil, sulphide gas, etc. [. . . ] Please take the time to read them as they will help you take full advantage of the unit's features. In the main part of the document, you will find a series of step-by-step procedures for each function available. The illustrations in the step-by-step procedures use three different symbols: PRESS PUSH HOLD DOWN E-6 Selecting the Automatic Operating Mode ENGLISH In the Automatic mode, the room temperature and the fan speed are controlled automatically. 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. 2 To select the AUTO mode, press the Mode button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in AUTO mode. Note x You can change modes at any time. 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. Result: x Each time you press Temperature buttons: - The temperature is adjusted by 1°C. x The air conditioner starts cooling, provided that the room temperature is than the selected temperature. - The quantity of air is adjusted automatically. E-7 Cooling Your Room You must select the COOL mode if you wish to adjust the : x Cooling temperature x Fan speed when cooling 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. 2 To select the COOL mode, press the Mode button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in COOL mode. Note x You can change modes at any time. E-8 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. Result: x Each time you press Temperature buttons: - The temperature is adjusted by 1°C. x The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature ; the fan will, however, operate. 4 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed : Automatic(rotated : Low Medium High ) 5 To control the direction of the air flow, refer to page 15. E-9 ENGLISH Heating Your Room (Except cooling only models) You can select the HEAT mode only in heat pump models. You must select the HEAT mode if you wish to adjust the : x Heating temperature x Fan speed when heating 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. 2 To select the HEAT mode, press the Mode button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in HEAT mode. Note x You can change modes at any time. E-10 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. [. . . ] Note x You can change modes at any time. 3 Select the fan speed by pressing the Fan button one or more times until the intended value is displayed: Low Medium High 4 To control the direction of the air flow, refer to page 15. E-14 Adjusting the Air Flow Direction (Except Duct Type) ENGLISH Depending on the position of the indoor unit, you can adjust the position of the air flow blade, thus increasing the efficiency of the air conditioner. 1 Press the Swing button. Result: The blade is moving between up and down. IMPORTANT When the air conditioner is first turned on, the blade is moved. 2 To stop the blade, press the Swing button again. To set to the required position, press the Swing button again when the blade is in the required position. E-15 Setting the On Timer The On Timer enables you to switch on the air conditioner automatically after a given period of time. You can set the period of time from 30 minutes to 24 hours. 1 To set the operating time, press the On Timer button one or more times until the required time is displayed. [. . . ]