User manual SAMSUNG MWR-TH00

[. . . ] x Do not use inflammable gases near the remote controller. x Do not spill water into the wired remote controller. x Do not operate the remote controller with wet hands. x Do not install the remote controller in a location where it will come into contact with the combustible gases, machine oil, sulphide gas, etc. [. . . ] Note x You can change modes at any time. E-6 3 To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 18C and 30C inclusive. Result: x Each time you press buttons: - The temperature is adjusted by 1C. x The air conditioner starts cooling, provided that the room temperature is than the selected temperature. - The quantity of air is adjusted automatically. E-7 ENGLISH Cooling Your Room You must select the COOL mode if you wish to adjust the : x Cooling temperature x Fan speed when cooling 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. 2 To select the COOL mode, press the button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in the COOL mode. Note x You can change modes at any time. E-8 3 To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 18C and 30C inclusive. Result: x Each time you press buttons: - The temperature is adjusted by 1C. x The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature ; the fan will, however, operate. 4 Select the fan speed by pressing the button one or more times until the intended value is displayed : Automatic(rotated : Low Medium High ) 5 To control the direction of the air flow, refer to page 15. E-9 ENGLISH Heating Your Room (Except cooling only models) You can select the HEAT mode only in heat pump models. You must select the HEAT mode if you wish to adjust the : x Heating temperature x Fan speed when heating 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped lt will start up normally after three minutes. 2 To select the HEAT mode, press the button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in HEAT mode. Note x You can change modes at any time. E-10 3 To adjust the temperature, press the buttons one or more times until the required temperature is displayed. Possible temperatures are between 16C and 30C inclusive. Result: x Each time you press buttons: - The temperature is adjusted by 1C. x The air conditioner starts heating, provided that the room temperature is lower than the selected temperature ; the fan will, however, operate. 4 Select the fan speed by pressing the button one or more times until the intended value is displayed : Automatic(rotated : Low Medium High ) 5 To control the direction of the air flow, refer to page 15. E-11 ENGLISH Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press (ON/OFF) button. Result: : x The On/Off indicator on the wired remote controller comes on. x The air conditioner runs in the mode selected when the unit was last used. IMPORTANT The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: x Plugged in x Stopped It will start up normally after three minutes. 2 To select the DRY mode, press the button until is displayed at the top of the wired remote controller. Result: : x The air conditioner runs in the DRY mode. [. . . ] x The selected mode and the temperature disappear on the display after 5 seconds. x The air conditioner will switch on automatically when the counter displayed on the remote controller reaches the setting time as disappearing the On timer setting. x You can see or change the setting mode and/or the temperature by pressing the button or the buttons after setting the On timer. Note E-16 To Cancel the On Timer 1 Press the Note button. x If you want to turn on the air conditioner before the timer reaches the setting time, press the button. E-17 ENGLISH Setting the Off Timer The Off Timer enables you to switch off the air conditioner automatically after a given period of time. [. . . ]