User manual SAMSUNG NP-R439E

[. . . ] SAMSUNG P428/R428/R429/R439/R478 User Guide Contents Chapter 1. Getting Started Cautions Regarding OS Support Before You Start Safety Precautions Important Safety Information Replacement Parts and Accessories Regulatory Compliance Statements WEEE SYMBOL INFORMATION Basic Items Overview Front View Status Indicators Right View Left View Back View Bottom View Attaching the Battery Connect the AC adapter Turn on the computer 6 7 9 23 25 27 40 41 42 42 43 44 45 46 46 47 47 48 Chapter 3. Settings and Upgrade LCD Brightness Control BIOS Setup Entering the BIOS Setup The BIOS Setup Screen 64 65 65 66 Proper Posture During Computer Use 20 Setting a Boot Password Changing the Boot Priority Upgrading Memory Battery Installing/Removing the Battery Charging the Battery Measuring the Remaining Battery Charge Extending the Battery Usage Time 68 70 71 73 73 74 74 75 Using the Security Lock Port 77 Turn on the computer 47 Chapter 4. Appendix Product Specifications 80 Using Sleep Mode 49 Chapter 2. [. . . ] Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limitesapplicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage radioélectrique édicté par Industrie Canada. The maximum allowed antenna gain for use with this device is 6dBi in order to comply with the E. I. R. P limit for the 5. 25- to 5. 35 and 5. 725 to 5. 85 GHz frequency range in pointto-point operation. As a general guideline, a separation of 20 cm (8 inches) between the wireless device and the body, for use of a wireless device near the body (this does not include extremities) is typical. This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your notebook, is well below the RF exposure limits as set by Industry Canada. This transmitter must not be collocated or operate in conjunction with any other antenna or transmitter except the installed Bluetooth transmitter. Operation of this device is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device. To prevent radio interference to licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that is installed outdoors is subject to licensing. Wireless devices are not user serviceable. Modification to a wireless device will void the authorization to use it. Contact manufacturer for service. Intentional Emitter per RSS 210 (If fitted with 2. 4G band or 5G band) Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2. 4GHz/5GHz Band, may be present (embedded) in your notebook system. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices. Wireless devices that may be in your system are only qualified for use in Canada if an Industry Canada ID number is on the system label. When using IEEE 802. 11a wireless LAN, this product is restricted to indoor use due to its operation in the 5. 15- to 5. 25-GHz frequency range. Industry Canada requires this product to be used indoors for the frequency range of 5. 15 GHz to 5. 25 GHz to reduce the potential for harmful interference to co-channel mobile satellite systems. High power radar is allocated as the primary user of the 5. 25- to 5. 35-GHz and 5. 65 to 5. 85-GHz bands. These radar stations can cause interference with and/or damage to this device. Telecommunications per DOC notice (for products fitted with an ICcompliant modem) The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operation, and safety requirements. The Department does not guarantee the equipment will operate to the users' satisfaction. Before installing this equipment, users should make sure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. [. . . ] Please refer to the system operation environment of this manual and operate and store the battery at room temperature. Installing/Removing the Battery 1 2 Shutdownthesystem, closetheLCD panelandplacethecomputerupside down on a flat surface. Pullthetwobatterylatchesoutwards , thenremovethebattery. 3 Toinstallthebatteryagain, slidethe batteryintothesystem. Thebatterylatchesmoveinwardsand fix the battery automatically. Charging the Battery 1 2 Attachthebatteryandconnectthe ACadaptertotheDC-injackofthe computer. Thebatterywillthenstart charging. Whenchargingiscomplete, theCharge LEDturnsred. Status Charging Check if the battery latch has been moved inwards. Charge LED Amber Green Off Charging complete AC adapter not connected Measuring the Remaining Battery Charge You can view the battery charge status by completing the following procedures. To use the shortcut key to view You can only use this function after installing Windows XP/Windows Vista/Windows 7 and installing the Easy Display Manager program with the system software media disk. [. . . ]