User manual SAMSUNG SC20F70HB

[. . . ] Do not allow the vacuum cleaner to run unattended at any time. Use the vacuum cleaner only for its intended use as described in these instructions. • Do not use the vacuum cleaner without a dust bin. Empty the dust bin before it is full in order to maintain the best efficiency. [. . . ] Failing to do so may result in injury or product damage. • Do not touch the power terminals on the back of the UV Brush with a metal pin or rod. This may result in electric shock or fire. • When the UV lamp is out of order, never disassemble or modify the product yourself. Please contact the manufacturer or service center for a replacement. • Since an internal discharge occurs within the UV Brush, never use the product near an inflammable spray or substance. • Take care not to touch the UV lamp window after using the UV Brush for an extended period of time as the surface of the window may be hot. • The UV Brush may start slowly at a low temperature due to the inherent characteristics of UV lamps. Please keep the UV Brush indoors. 06_ safety information contents ASSEMBLING THE CLEANER 08 OPERATING THE CLEANER 09 09 09 10 12 13 Power cord ON/OFF Switch Power control Using the UV brush (SC20F70U Series) Using the Dust Sensor (Option) TOOLS AND MAINTENANCE FILTER 15 TROUBLESHOOTING 15 17 20 20 21 22 23 24 25 Using accessory Maintain floor tools Cleaning the Dust Sensor (Option) Emptying the dust bin Clean the Grille Clean the dust bin with water Cleaning the dust filter Cleaning the dust filter Cleaning the outlet filter 26 contents _07 assembling the cleaner OPTION • For storage, park the floor nozzle. Please do not pick up a machine while the floor nozzle parked 08_ assembling the cleaner operating the cleaner POWER CORD 02 operating the CAUTION • When removing the plug from the electrical outlet, grasp the plug, not the cord. cleaner ON/OFF SWITCH operating the cleaner _09 POWER CONTROL Hose Handle (SC20F70H Series) 1. ON/OFF [   ] Button -- Press the ON/OFF button to operate the vacuum cleaner. 2. [(-/+)] Button -- Press the MODE button repeatedly to select the correct mode. • It is advisable to select the (Max) suction strength setting. • UV sterilization cannot be activated by itself. 3. When you have finished UV cleaning, press the [  • Press the [   ] button to stop the cleaner.  ] button. -- For safety reasons, UV brushing only runs for 30 minutes and then stops operating. To resume the operation, press the [SUCTION (-/+)] button again. CAUTION The UV brush, which is inserted into the hose handle (not directly connected to the telescopic pipe), is dedicated for bedclothes. 12_ operating the cleaner operating the cleaner USING THE DUST SENSOR (OPTION) Dust Sensor Operations 02 • Indicates the amount of sucked in dust so that users can experience the successful operation of the product while cleaning the room. • Green : When the amount of sucked in dust is small. • Red : When the amount of sucked in dust is large. operating the • The dust sensor is automatically turned on when the cleaner runs and turned off when the cleaner is stopped. • Since the dust sensor runs on battery power, there is no separate switch. cleaner Installing the Batteries 1 2 Check the polarities 3 • If the dust sensor doesn’t work even after cleaning the sensor, replace the batteries with new ones. • Do not disassemble or recharge the used batteries. • Do not heat the batteries or put them in a fire. • Check the polarities (+ , -) before inserting the batteries. • Put the used batteries into the battery recycle bin. [. . . ] If the light comes on after emptying the dust bin, cleaning the grill, please check the dust filter. 03 tools and maintenance filter tools and maintenance filter _23 When suction is noticeably reduced or vacuum cleaner abnormally overheats, please clean the dust filter. CLEANING THE DUST FILTER 1 2 3 Take the dust bin out by lifing the handle. Pull the dust bin cover to open. Remove the filter from the dust bin. 4 5 6 Shake the filter over a garabage can to remove loose dust, then wash the filter with water. Let the filter dry in the shade for more than 12 hours. Put the filter into the dust bin. 7 8 Close the dust bin cover. To close the dust bin cover, filter should be assembled. After the take the dust bin in main body, close the cover dust when you hear the " click" sound. Make sure the filter is completely dry before putting it back into the vacuum cleaner. If dust filter is damaged or deformed please replace it. 24_ tools and maintenance filter CLEANING THE OUTLET FILTER 1 2 3 03 tools and Take the dust bin out by lifing the handle. Pull out the HEPA filter. Separate the filter and holder by pulling. 4 5 6 maintenance filter Throw away the dirty filter. Assemble the new filter in holder. Assemble the filter and holder in main body. • When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats, please clean the outlet filter. If cleaning does not resolve the problem Please replace blocked out filter. [. . . ]